Vinten 3702 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 84

background image

26

Servicing

Nitrogen charging

3

The pneumatic system of the pedestal is a closed circuit, and normally maintains a given pressure for a

long period. However, the charge pressure may need to be varied for load changes in which case, the nitrogen
charging procedure given in Section 2 must be followed.

Leak check

4

Carry out the leak check as follows:

4.1

Place a suitable load (approximating to normal payload) on the head mounting platform,

disengage the two platform locking bars and raise the column to its full extent.

4.2

Remove load from head mounting platform.

4.3

Lay the pedestal on its side so that the steering ring supports the column.

4.4

Apply a soap and water solution to the manifold block, the area at the base of the ram, the safety

valve and the charging valve. The appearance of bubbles indicates leaks.

4.5

If leaks are apparent, consult

for the appropriate remedial action.

Safety valve check.

5

It is suggested that this check be carried out at yearly intervals. Proceed as follows:

5.1

Fit nitrogen charging equipment (Part No. 3702-32) or similar to charging point and depressurize

pedestal completely.

5.2

Referring to

, remove safety valve (2) and bonded seal (1) from tank. Remove nitrogen

charging equipment from charging point.

5.3

Connect nitrogen charging equipment to nitrogen supply ensuring that a suitable pressure

reduction valve is fitted between the gas cylinder and the supply point

5.4

Connect pressure relief valve to outlet side of charging equipment.

5.5

Set pressure reduction valve to 280psi (19.31bar) and pressurize line, increasing pressure in

steps of 5psi (0.34bar) until relief valve opens. The valve should operate at 308psi (21.24bar) However,

WARNING!: This pedestal must be charged only with clean dry air or nitrogen. A pres-
sure reducing valve must be fitted to the pressure line between the nitrogen cylinder
and the outlet connection of the hose. The reducing valve must be screwed into the
nitrogen cylinder outlet. The maximum pressure on the outlet side of the reducing valve
when charging this pedestal must not exceed 280psi (19.31bar).

NOTE:

It is recommended that this check is only carried out when it is apparent that a pressure
loss has taken place. To carry out the check it is necessary that the column be at full
extension.

«
...
24
25
26
27
28
...
»

Содержание 3702





















































































Отзывы:

Нет отзывов

Похожие инструкции для 3702

Бренд: 4B Страницы: 12

POVCAM AG-HCK10G

Бренд: Gates Страницы: 2

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: Galeo Страницы: 19

Бренд: Gardener's Страницы: 2

AERASGARD RCO2-W

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Labona Страницы: 12

Бренд: Tait Страницы: 46

Бренд: Tait Страницы: 9

Бренд: Tait Страницы: 89

Бренд: Tait Страницы: 20

Бренд: Front Runner Страницы: 5

Бренд: Taffio Страницы: 8

DGIPOD-4655 - DATASHEET FOR IPHONE

Бренд: I.SOUND Страницы: 1

Dual Shock Rally Master

Бренд: Trust Страницы: 9

Бренд: media-tech Страницы: 13

Бренд: matev Страницы: 23

MagicComfort MSH200

Бренд: Waeco Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды