Vinten 3702 Скачать руководство пользователя страница 37

Страница: 37 / 84

7.3

Lay the pedestal on its side.

7.4

Referring to

Fig 6.6

slacken the four screws (10) at each end of the manifold (4) to allow the 'O'

ring seal (8) to unseat and any residual pressure in the tank to exhaust. Remove screws (10) and
washers (9).

7.5

Withdraw the first stage piston (5) and the manifold (4) together from the bore of the first stage

cylinder.

7.6

Close the column to its lowest position.

7.7

Slacken two screws (17) and remove the cords (21) from cord clamps (19). Note the

arrangement of the cord in the clamp.

7.8

Referring to

Fig 6.7

remove circlip (26) from the end of the first stage cylinder (6) to release it

from the ram plate (31).

7.9

Remove eight screws (32), separate the first stage ram plate (31) from the column bottom tube

(33) and allow it to hang on the chains.

7.10 The second stage cylinder (4) and the first stage cylinder (6) may now be withdrawn from the
second stage ram plate (34).

7.11 Service the ram assembly as necessary. Referring to

Fig 6.7

, fit new 'O' ring seals throughout.

Pack between bearings and coat walls of piston and cylinders with Chesterton white grease No. 622

(Section 3)

Safety valve, charging valve and pressure gauge

To replace a defective safety valve, charging valve or pressure gauge proceed as follows:

8.1

Connect nitrogen charging equipment to the charging point and completely depressurize the

pedestal.

8.2

Remove the defective item and replace with new or serviceable item. Fit new bonded seals.

8.3

Charge the pedestal

(Section 2)

8.4

In the case of safety valve replacement refer to

Section 4

8.5

Carry out leak check

(Section 4)

Содержание 3702





















































































Результаты поиска

Содержание 3702

Отзывы:

Похожие инструкции для 3702

Бренды по названию

Популярные бренды

Vinten 3702, Руководство по обслуживанию

Результаты поиска

Содержание 3702

Отзывы:

Похожие инструкции для 3702

Бренды по названию

Популярные бренды