Vinten 3702 Скачать руководство пользователя страница 27

Страница: 27 / 84

a tolerance of ± 0.42 bar (6 psi) is permitted, and provided that the valve opens between 20.82 bar and
21.65 bar (302 psi and 314 psi) it can be considered that it is functioning correctly.

5.6

Fit new, or refit correctly functioning safety valve to tank, using a new bonded seal (1). The

bonded seal should be fitted onto the threaded portion of the valve. Torque tighten the safety valve to
20lbf ft.

5.7

Charge pedestal as described in

Section 2

Chain tension.

Check the chain tension as follows

(Fig 4.1)

6.1

Remove cable guard and covers.

6.2

Check the tension of the steering chain. This should be such that there is little or no deflection of

the chain on the side opposite the adjuster. If unsatisfactory, adjust as

Para 10

WARNING!: If valve setting is not satisfactory renew the complete valve assembly. DO
NOT, under any circumstances, attempt to adjust the valve.

Fig 4.1 Chain tension adjustment

Little or no

deflection

here

(1)

(2)

(3)

STEERING CHAIN

Max 10 mm (3/8 in.) deflection here

WHEEL CHAIN

(4)

(5)

Содержание 3702





















































































Результаты поиска

Содержание 3702

Отзывы:

Похожие инструкции для 3702

Бренды по названию

Популярные бренды

Vinten 3702, Руководство по обслуживанию

Результаты поиска

Содержание 3702

Отзывы:

Похожие инструкции для 3702

Бренды по названию

Популярные бренды