Vinten 3702 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 84

background image

36

6.6

Disconnect the cords (26) from the adjusters (27) noting the way in which the cords are secured

in the adjusters.

6.7

Referring to

remove two screws (18) securing each of the four top track clamps (19) and

remove the clamps.

6.8

Withdraw the bottom tube, complete with the centre tube and the top tube, from the flange end of

the fixed tube. Secure the free ends of the tracks to the bottom tube.

6.9

Referring to

remove four screws (17) which secure the centre tube cover plate (16) and

remove the plate.

6.10 Referring to

remove the screws (32) which have been used to secure the first stage ram

plate (31) to the bottom tube (33).

6.11 Remove joining links (37) to disconnect the chains (38) from the adjusters (28) in the ram plate.
Withdraw the cords which pass through the plate.

6.12 Referring to

remove two screws (25) which secure each of the bottom pulley shafts (26)

to the bottom tube and remove the pulley assemblies. Draw the ends of the cords back into the bore of
the bottom tube.

6.13 Withdraw the centre tube, complete with the top tube, from the lower end of the bottom tube.
Secure the free ends of the tracks to the centre tube.

6.14 Referring to

remove four screws (32) which secure the second stage ram plate (34) to the

centre tube (35).

6.15 Referring to

remove two screws (2) securing each of the four top track clamps (3) and

remove the clamps.

6.16 Withdraw the top tube from the lower end of the centre tube, allowing the chains to run over the
sprockets inside the centre tube. Secure the free ends of the tracks to the top tube.

Ram

7

To remove the ram assembly without removing the column:

7.1

Remove any load from the head mounting platform.

7.2

Connect nitrogen charging equipment to the charging point and completely depressurize the

pedestal.

NOTE:

Cords which have been disconnected from the adjusters must be replaced with new cords
on reassembly.

NOTE:

Access to all parts of the column at this point is possible. The replacement procedure for
piece parts is self-evident.

NOTE:

The ram assembly consists of a first stage piston inside a first stage cylinder which is, in
turn, inside a second stage cylinder.

«
...
34
35
36
37
38
...
»

Содержание 3702





















































































Отзывы:

Нет отзывов

Похожие инструкции для 3702

Бренд: Davis Instruments Страницы: 16

Бренд: Samsung Страницы: 15

Бренд: Hama Страницы: 60

Бренд: BAFANG Страницы: 4

Бренд: S-BOL Страницы: 3

Бренд: hepco & becker Страницы: 4

Бренд: CAME Страницы: 2

Бренд: VOLTCRAFT Страницы: 2

BOS 21M-UUI-RP30-S4

Бренд: Balluff Страницы: 70

Бренд: Swann Страницы: 12

Бренд: Satlink Страницы: 16

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Ceiling Trim Kit for Home2 Series

Бренд: Elite Screens Страницы: 8

Telaire Ventostat T8100 NS Series

Бренд: Amphenol Страницы: 4

6086 Canon HF G30

Бренд: Ikelite Страницы: 8

Бренд: Mystic Romance Страницы: 10

Бренд: Lambrecht Страницы: 11

Бренд: Peco Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды