Vintage Air 474171 Скачать руководство пользователя

Страница: 15 / 16

904270 REV D 4/14/15, 1969-72 NOVA w/o AC CONTROL PANEL KIT PG 15 OF 16

COLD

HOT

OFF

DASH

DEF

OPERATION OF CONTROLS

DEFROST/ DE-FOG

MODE

HEAT MODE

A/C MODE

BLOWER SPEED

ADJUST TO DESIRED

SPEED

TEMPERATURE LEVER

SLIDE THE TEMPERATURE

LEVER ALL THE WAY DOWN

TO THE HOT POSITION.

(SLIDE LEVER UP OR DOWN

TO DESIRED TEMPERATURE)

SLIDE THE LEVER TO

THE “FLOOR” POSITION

MODE LEVER

BLOWER SPEED

ADJUST TO DESIRED

SPEED

TEMPERATURE LEVER

SLIDE THE LEVER TO

THE “DEF” POSITION

MODE LEVER

COLD

HOT

OFF

DASH

DEF

BLOWER

SPEED

TEMPERATURE

LEVER

MODE

LEVER

BLOWER SPEED

ADJUST TO DESIRED

SPEED

TEMPERATURE LEVER

IN A/C MODE SLIDE

THE TEMPERATURE LEVER

ALL THE WAY UP TO

ENGAGE COMPRESSOR.

(SLIDE LEVER UP OR

DOWN TO ADJUST

DESIRED TEMPERATURE)

SLIDE THE LEVER TO

THE “DASH” POSITION

MODE LEVER

NOTE: CONTROLS MUST BE CALIBRATED FOR PROPER OPERATION-REFER TO CONTROL PANEL
INSTRUCTIONS.

THE TEMPERATURE LEVER TOGGLES BETWEEN A/C AND HEAT MODES. FOR A/C MODE SLIDE THE
TEMPERATURE LEVER ALL THE WAY UP, FOR HEAT MODE SLIDE THE LEVER DOWN TO DISENGAGE
THE COMPRESSOR, THEN MOVE THE LEVER TO SELECT DESIRED TEMPRATURE.

NOTE: EACH TIME THE SYSTEM TOGGLES BETWEEN MODES, THE BLOWER WILL MOMENTARILY
CHANGE SPEEDS.

ALL SWITCHES ARE VARIABLE BETWEEN POSITIONS, SYSTEM WILL PERFORM A BLEND BETWEEN
THE FUNCTIONS.

COMPRESSOR IS FORCED

ON IN DEFROST MODE.

THERE IS NO NEED TO

ADJUST THIS LEVER.

Содержание 474171

















Результаты поиска

Содержание 474171

Отзывы:

Похожие инструкции для 474171

Бренды по названию

Популярные бренды

Vintage Air 474171, Руководство пользователя

Результаты поиска

Содержание 474171

Отзывы:

Похожие инструкции для 474171

Бренды по названию

Популярные бренды