Vingtor Stentofon 3005050028 Скачать руководство пользователя страница 19

Страница: 19 / 79

MARINE MASTER CLOCK

Document: 1717en19.doc

Author: PM

User Manual

Date: 2017-12-22

Page: 16 of 51

WESTERSTRAND URFABRIK AB

P.O. Box 133

Tel. +46 506 48000

Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA

Fax. +46 506 48051

E-mail:

[email protected]

Alarm list

The following alarms are available

Type of alarm

Indication

Reason for alarm

Action

NO RADIO

Red alarm LED lit.
General alarm relay activated.

The Master Clock has
not been synchronised
within the alarm limit.

Check the external
synchronisation source. If
no external source is used
inactivate the alarm. See
special function/ setup
sync. source page 36.

UF LOW

52 Red alarm LED lit.

General alarm relay activated.

Impulse voltage below
alarm limit.

Remove connected clocks
and clear the alarm. If OK,
check clocks and wiring.

SHORT CIRCUIT

Red alarm LED lit.
Common alarm relay activated.

Short circuit on impulse
amplifier.

Remove short circuit.
If OK, clear the alarm.

CURRENT LOW

61 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 1 is below
alarm limit.

Check output connections.
If OK, clear the alarm.

CURRENT LOW

62 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 2 is below
alarm limit.

Check output connections.
If OK, clear the alarm.

CURRENT LOW

63 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 3 is below
alarm limit.

Check output connections.
If OK, clear the alarm.

CURRENT LOW

64 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 4 is below
alarm limit.

Check output connections.
If OK, clear the alarm.

CURRENT HIGH

71 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 1 is above
alarm limit.

Check output load.
If OK, clear the alarm.

CURRENT HIGH

72 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 2 is above
alarm limit.

Check output load.
If OK, clear the alarm.

CURRENT HIGH

73 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 3 is above
alarm limit.

Check output load.
If OK, clear the alarm.

CURRENT HIGH

74 Red alarm LED lit.

General alarm relay activated.

Impulse current on
output no. 4 is above
alarm limit.

Check output load.
If OK, clear the alarm.

CURRENT HIGH

75 Red alarm LED lit.

General alarm relay activated.
(Remark:

Alarm 75 is only used

in a 3-wire Forward/Reverse
system.)

Impulse current on
output no. 4 is above
alarm limit.

Check output load.
If OK, clear the alarm.

Содержание 3005050028
















































































Результаты поиска

Содержание 3005050028

Отзывы:

Похожие инструкции для 3005050028

Бренды по названию

Популярные бренды

Vingtor Stentofon 3005050028, Техническое руководство пользователя

Результаты поиска

Содержание 3005050028

Отзывы:

Похожие инструкции для 3005050028

Бренды по названию

Популярные бренды