Vimar ELVOX SL230.T, Руководство по подключению и эксплуатации

Страница: 25 / 74

14. Dip switch functions.
Number Status Function Description
DSW1
DIP 1
OFF Automatic closing disabled -
ON Automatic closing enabled The open gate is closed automatically after the pause time.
DIP 2
OFF Operating logic: Opens-Stops-Closes-Stops
It modifies the operating sequence of inputs SEQ (sequential) and PED (pedestrian) also via
remote control.
ON Operating logic: Opens-Closes
DIP 3
OFF Courtesy function on photocell disabled -
ON Courtesy function on photocell enabled Reduction to 3sec of the residual pause time after passing over photocells.
DIP 4
OFF Collective operating logic disabled -
ON Collective operating logic enabled When opening the gate, it ignores any controls and reloads the pause time when on pause
DIP 5
OFF Pre-flashing disabled -
ON Pre-flashing enabled The flashing lamp starts flashing 3 seconds before the start of each movement
DIP 6
OFF Flashing built into the flashing lamp. It configures the output for flashing lamps with independent flashing.
ON Flashing controlled by the control unit. It configures the output for flashing lamps without independent flashing.
DIP 7
OFF Gate opens towards the Right Configures gate opening towards the right
ON Gate opens towards the Left Configures gate opening towards the left
DIP 8
OFF P.OUT 2
nd
remote control channel Input P.OUT works as 2
nd
radio channel
ON P.OUT Safety test (Photo-test) Input P.OUT controls the operation of the safety devices
DSW2
DIP 1
OFF Non-resistive edge SOP SOP input configured to connect a non-resistive sensitive edge.
ON 8K2 resistive edge SOP SOP input configured to connect an 8K2 resistive sensitive edge.
DIP 2
OFF Soft Start disabled The gate begins moving at constant speed
ON Soft Start enabled The gate begins moving at a progressive speed
15. Troubleshooting.
Problem Cause Solution
The automatic gate system does not
work
No mains supply Check the power line switch
Blown fuses Replace the fuses with others of the same value
Control and safety inputs not working Check the diagnostics LEDs: DL1 P.IN, DL3 STOP, DL5 SCL, DL6 SOP must be on.
Safety device test failed Check the operation of the safety devices installed if 4 simultaneous flashes of the following occur:
LED DL.S, indicator light and flashing lamp.
Triac operating control test failed Replace the control unit if 2 simultaneous flashes of the following occur: LED DL.S, indicator light
and flashing lamp.
(Only for motor models with Encoder)
Motor not working properly
(Only for motor models with Encoder) Replace the motor if 3 simultaneous flashes of the following
occur: DL.S LED, indicator light and flashing lamp .
The limit switches remain activated. Check the capacitor and/or wiring of the board/motor and/or the presence of any obstacles in
deceleration zones if 6 simultaneous flashes of the following occur: DL.S LED, indicator light and
flashing lamp.
The limit switches are not activated. Check the fixing of the limit switch cams and/or whether you have closed the release if 7
simultaneous flashes of the following occur: LED DL.S, indicator light and flashing lamp.
You cannot save the remote controls Batteries of the remote control discharged Replace the batteries
Remote control not compatible with the first one
saved
The first saved rolling-code remote control configures the control unit to save only rolling-code
remote controls and not hard coded remote controls.
Reached memory saturation Delete at least one remote control or add an external receiver (maximum capacity 250 rolling-code
remote control codes)
The remote control does not work Batteries of the remote control discharged Replace the batteries
You cannot enter travel programming Safety devices open Check the diagnostics LEDs: DL1 P.IN, DL3 STOP, DL5 SCL, DL6 SOP must be on.
As soon as the gate starts it stops and
reverses
Low acceleration on starting Increase the TR2 TORQ trimmer
During slowdown, the gate stops and
reverses
Slowdown speed too low Increase the TR4 SL trimmer
The gate stops just before the limit
switch trips
The limit switch does not work properly Advance the limit switch cam
Declaration of Conformity.
Vimar S.p.A. declares that the device complies the following directives:
2014/53/EU (RED)
2014/30/EU (EMC)
2014/35/EU (LVD)
2006/42/EC (Machinery Directive)
The full text of the EU declaration of conformity is on the product sheet available on the following website: www.vimar.com .
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
25
SL230.T - SL230.T.120
EN