Viking GB 460, Инструкция по эксплуатации

Страница: 69 / 656

67
DE
FR
NL
IT
ES
PT
NO
SV
FI
DA
PL
SK
HU
HR
EN
0478 216 9905 A - EN
2. To install:
●
Clean the blade disc.
●
Reverse blade (3) and place onto the
blade disc with the sharp edge exposed
and align the bores.
●
Insert screws (1) through the bores and
screw on nuts (2). Tighten nuts (2) to
8
-
-
1
0 Nm
.
Reversing the three blades of the hard
material blade disc (Figure
B
):
1
. Removing:
●
Unscrew the screws (4) and M8
screws (5) and remove them together
with the nuts (6) and M8 nuts (7).
●
Lift off the blades (8) and blade (9).
2. To install:
●
Clean the blade disc.
●
Reverse the blades (8) and place onto
the blade disc with the sharp edge
exposed and align the bores.
●
Insert screws (4) through the bores and
screw on nuts (6). Do not tighten.
●
Press the two blades (8) together (see
small illustration) and hold. There must
be no gap between the two blades (8).
●
Tighten nuts (6) to
8
-
-
1
0 Nm
.
●
Reverse the blade (9) and place onto
the blade disc with the sharp edge
exposed.
●
Insert the M8 screws (5) through the
bores, screw on the M8 nuts (7) and
tighten to
1
6
-
20 Nm
.
1
2.8 Sharpening the blades
●
Removing the blade discs. (
Ö
12.3)
●
Remove the blade. (
Ö
12.7)
Sharpening angle:
The sharpening angle for all the blades is
30° .
Instructions for sharpening the blades:
The following points must be observed
when re-sharpening the blades:
●
Cool the blades when sharpening,
e.g. with water. The blade must not be
allowed to display blue colouring, as
this would reduce its cutting quality.
●
Sharpen the blade evenly to prevent
vibrations due to imbalance.
●
Check blades for damage before
installing: The blades must be replaced
if notches or cracks are visible or if the
blades have reached the wear limits.
●
Re-sharpen the cutting edges to the
specified sharpening angle.
●
Sharpen the blades against the cutting
edge.
●
After sharpening, remove any
sharpening burr at the cutting edge
using fine sandpaper.
1
2.9 Wear limits of the blades
1
Blade overview
2 wing blades (1)
6 blades (2)
1 blade (3)
1 counter-blade (4)
Soft material blade disc:
The soft material blade disc is fitted with
four blades.
Hard material blade disc:
The hard material blade disc is fitted with
two blades and one chipping blade.
●
Removing the blade discs. (
Ö
12.3)
There must be no gap between the
two blades (8) following installation.
A gap between the two blades
impairs the feeding function.
We recommend that all blades are
sharpened only by a specialist
dealer, as the function (drawing in
of shredding material, durability of
the cutting edges etc.) of the
garden shredder may deteriorate if
blades are ground incorrectly
(wrong sharpening angle,
imbalanced due to unevenly ground
blades etc.).
Always wear safety glasses when
sharpening. Make sure that others
are kept out of the danger area.
The blades must be reversed or
replaced before reaching the
specified wear limits (A, B, C, D).
VIKING recommends VIKING
specialist dealers.
The specified values should be
measured at several points (two or
three recommended) along the
cutting edge on all the blades.
Use the smallest value for a blade.
We recommend that you always
reverse or replace all the blades at
the same time.
29