9
LP/Propane Tank Connection
The o
utdoor
wok/cooker
orificed for use with LP/Propane gas come equipped with a high capacity hose/regulator
assembly
for connection to a standard 20 lb. LP/Propane cylinder equipped with a Type 1, QCC-1 connector.
(See LP/
Propane tank
requirements on page 6). Hose assembly must comply with Elastomeric Composite Hose and Couplings
for Conducting
Propane and Natural Gas, CAN/CGA-8.1 standard or the Thermoplastic Hose and Hose Couplings
for Conducting
Propane and Natural Gas CAN1-8.3 standard. (See LP/Propane tank requirements below). Each tank
is supplied with a
dust cap. Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the
type of dust cap on
the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may
result in leakage of
propane.
Built-in installations must be plumbed using a fixed/hard line if the unit is going to be operated at a distance exceeding
3 feet (0.91 meters) from the fuel supply per ANSI Z21.24. Also, in a built-in construction where an LP/Propane tank is
going to be used, there MUST be some type of support (braces, cut-out, etc.) to prevent tank from moving within the
installation. The support must also allow the LP/Propane tank to withstand a horizontal tipping force equal to the weight
of the tank without tipping over. The tank can not tip over or deflect more than 1.00 inch when a 38 lb. horizontal force
is applied to a 20 lb. LP/Propane tank.
Connection: 1/2” (1.3 cm) NPT male with a 3/8” (.95) flare adapter
Operating Pressure: 10.0” W.C.P.
To connect to LP/Propane regulator/hose assembly:
Although the flow of gas is stopped when the quick disconnect system is disconnected as part of its safety feature, you
should always turn the LP/Propane tank main valve “OFF” after each use and during transport of the tank or unit. First
connect the regulator to the unit by screwing the 3/8” flare coupling to the 3/8” flare adapter. Connect to the tank valve
by screwing the Type 1, QCC-1 connector to the LP/Propane tank. Open the tank valve and check the connection
between the regulator and the Type 1, QCC-1 fitting for leaks with a soapy water solution. If bubbles appear, tighten the
connection. Repeat until all leaks have been stopped. ALWAYS CHECK FOR LEAKS AFTER EVERY LP/PROPANE TANK
CHANGE. Any joint sealant used must be an approved type and be resistive to the actions of LP/Propane gas.
LP/Propane Tank Requirements
A dented or rusty LP/Propane tank may be
hazardous and should be checked by your tank
supplier. Never use a cylinder with a damaged
valve. All tanks should be equipped with an OPD
(overfilling protection device). This is a DOT
requirement for all tanks purchased after October
1, 1998 and will ensure that the tank is not
overfilled. The LP/Propane tank should be a
standard 5-gal, 20 lb. gas cylinder tank
approximately 12” in diameter and 18” high which
must be constructed and marked in accordance
with the Specifications for LP/Propane Gas
Cylinders of the U.S. Department of Transportation
(D.O.T.) or the National Standard of Canada,
CAN/CSA-B339, Cylinders, Spheres and Tubes for
Transportation of Dangerous Goods; and
Commission. The cylinder connection device must
be compatible with the Type 1, QCC-1 connector
on the outdoor cooking appliance. All LP/Propane
tanks must be mounted in a vertical position for
proper ventilation. The cylinder must be provided
with a shut-off valve terminating in an LP/Propane
gas supply cylinder valve outlet specified. The
cylinder supply system must be arranged for vapor
withdrawal and provided with a listed overfilling
prevention device. If the appliance is stored
indoors the cylinder must be disconnected and removed from the appliance. Each tank is supplied with a dust cap. Place dust
cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that
is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. Cylinders must be stored
3/8”
3/8”
male
male
flare
flare
adapter
adapter
1/2”
NPT
from
Manifold
Type 1,
QCC-1
connector
3/8” male
flare adapter
Regulator
Assembly
NOTE: Tank must be
mounted in vertical position
for proper Ventilation
