background image

 

LT0186 Issue 2.80 

         27 July 2012 

Page 5 of 10 

INPUT WIRING DETAILS

 

 

3.1  Auto/Isolate/Evac Switch. 

 

     

 

 

 

 
The use of the Auto/Isolate/Evac switch is not recommended in fire panels compliant with AS 4428.1 or AS 7240.2, as 
the isolate facility on this switch is a duplication of the AS 4428 Warning System Isolate or AS 7240 Alarm Devices 
Disable function already provided on these panels, and there is no indication of the Isolate position.   
 
However, the switch may be useful with older AS1603.4 fire panels, in which case the Isolate position should be 
indicated. 
 
An LED (and resistor) could be wired to turn on in the Isolate position via a spare switch contact (Figure B), or a fault 
could be generated on the fire panel when the switch is in the Isolate position.  For example, wire the ELD 0V connection 
through the Auto and Evacuate switch contacts so a fault is generated in the Isolate position (Figure C). 
 
Alternatively, if the Isolate position is to be disabled (but the Auto and Evacuate positions retained) remove the 10k 
resistor from the Isolate switch and blank off the word 

“Isolate” on the l

abel. 

 
 
 
 
 
 
 
 
 
 
 
 
 

ISOL

+24V

AUTO

Yellow
LED

2K7

0V

EVAC

 

ISOL

AUTO

ELD

0V

EVAC

COM

 

A/I/E- Switch Wiring 

Figure A 

Isolate Indication via Spare Switch Pole 

Figure B 

Using Isolate Position to Generate Fault 

Figure C 

 

3.2  Background Music/Remote Paging 
 

An external audio source can be connected to the T-GEN MUSIC input, J9, for background music, external paging, etc.  
This source must have an isolated output, otherwise an audio isolating transformer, e.g. the ALIM9706 (part number 
PA0646), must be used.  Refer to LT0372 for the ALIM wiring arrangement. 
 
A background music loom adapter consisting of a 2 way plug with red (SIG) and black (GND) wires is supplied with the 
T-GEN. 

 
 
 
 
 
 
 
 

Remote paging (non-emergency) can be achieved by using the PA0688 microphone preamp board.  Refer to LT0371 for 
details.

 

 

3.3 Microphone  

 

An emergency PA microphone (part number ME0290) can be connected to J1 on the T-GEN. 

 
 
 
 
 
 
 

For a remote emergency PA microphone, refer to LT0371 for using a PA0688 microphone preamp. 

 

T-GEN 50 

Master 

Music             
J9 

 

Sound System 

 

SIG 

2.5Vrms max 

GND 

Mic Preamp 

(see LT0371)

 

 

Screened cable 

J1-1 MIC- 
J1-2 MIC+ 
J1-3 PTT  
J1-4 PTT

 

T-GEN 50 

MASTER 

A/I/E-               
 
0V

 

10k

 

ISOL

 

EVAC

 

AUTO

 

RED 
 
BLACK 

Содержание T-GEN 50











Отзывы: