Viessmann VITOFLEX 300-RF Скачать руководство пользователя

Страница: 38 / 100

4.8 Mobile cleaning equipment accessories

Cleaning set with ash vacuum cleaner, 90 l

Boiler cleaning set

For part no., see pricelist

Standard delivery

■ WSZ 2210 ash vacuum cleaner
■ Ash container, 90 l capacity
■ Cyclone cover for 90 l ash container

■ Trolley with toggle fastener
■ Metal hose 2 m
■ Metal hose 3 m
■ Vacuum gun, DN 50

Cleaning set with ash vacuum cleaner, 240 l

Boiler cleaning set

For part no., see pricelist

Standard delivery

■ WSZ 2210 ash vacuum cleaner
■ Ash container 240 l capacity

■ Cyclone cover for 240 l ash container
■ Metal hose 2 m
■ Metal hose 3 m
■ Vacuum gun, DN 50

Available ash vacuum cleaner accessories:

Boiler room cleaning accessory set:
■ The room cleaning accessory set is offered as a complement to

the ash vacuum cleaners.
See page 39.

Ash container:
■ Ash bin 90 l, reserve
■ Ash container 240 l, reserve
■ 800 l ash container, with cover

See page 39.

Ash vacuum cleaner

WS ash vacuum cleaner

For part no., see pricelist

Ash vacuum cleaner with body made from GRP and with low filter
loading on the cell filter. Motors are cooled separately.

DS ash vacuum cleaner

For part no., see pricelist

Ash vacuum cleaner with body made from GRP and with low filter
loading on the cell filter. Motors are cooled separately.

Specification
Ash vacuum cleaner

WSZ 2210

Only available as cleaning set

Power consumption

2 x 1000

1 x 3600

1 x 7500

Rated voltage

230

400

Weight

114

Vacuum

mm WC

1950

2100

3300

Air flow rate

m³/h

270

430

490

Filter surface area

m²

1.0

2.6

Sound level

dB(A)

Maximum total length of permanently installed
pipework for the flue gas extraction system

Permanently installed pipework

is not permissible

100

Installation accessories

(cont.)

Viesmann

VITOFLEX 300-UF

5682428

Содержание VITOFLEX 300-RF





































































































Результаты поиска

Содержание VITOFLEX 300-RF

Отзывы:

Похожие инструкции для VITOFLEX 300-RF

Бренды по названию

Популярные бренды

Viessmann VITOFLEX 300-RF, Техническое руководство

Результаты поиска

Содержание VITOFLEX 300-RF

Отзывы:

Похожие инструкции для VITOFLEX 300-RF

Бренды по названию

Популярные бренды