background image

GB

General notice (liability): the details of this technical documents serve for description. Consents regarding the availability of certain features or
regarding a certain purpose always require a special written agreement.

Page 8 GB 

 

 

Right reserved to make technical changes!

GB

3.3   Assembly of the wall panels

 

 

Clean the interior flooring panel in the area of the interior 

 

  wall plating C with isopropanol. Adhere the enclosed sealing

 

  gasket (D) to the cleaned edge of the interior flooring plate.

 

  Remove the protective foil from the sealing gasket.

 

  Begin the wall assembly with the corner panels. Connect the

 

  panels using the cam locks.

3.4   Assembly of the door

 

 

The one piece door is supplied complete with the door 

 

  frame.

 

 

During assembly ensure that the doorframe is installed 

 

  perfectly horizontally and vertically (plumb Iine).

3.5   Assembly of the ceiling panels

 

 

When installing a wall-hanging unit, it must be hung on the  

 

  side section of the door frame or on the wall before 

 

  installing the ceiling elements. During installation ensure  

 

  that the evaporator fan does not blow onto the door leaf and  

 

  the pressure compensation valve.

 

  Place the ceiling panels in position and tighten the cam

 

  locks.

 

     

Note!

 

 

lf the panels are uneven, release the cam locks and adjust

 

  the panels. Tighten all cam locks (wall/ceiling, wall/wall, 

 

  wall/floor) again.

3.6   Assembly of the door threshold

 

 

Place the stainless steel door threshold (G) in the middle of

 

  the door opening and adjust. Drill holes for fastening of the

 

  door threshold (ø 3.3 mm)

 

   

Do not drill extra holes due to possible heating

 

   

cable underneath. Danger to life!

 

  In order to seal the threshold securely against penetrating 

 

  damp, apply a bead of polyurethane sealant (L) to the front

 

  of the door sill at the bottom, on the inside and on the sides.

 

  Place door threshold plate on the flooring panel, adjust and

 

  rivet in place using enclosed rivets.

 

  Seal the threshold with PU sealant on the sides of the door

 

  opening and to the floor.

 

  Smooth off excessive sealant.

D

C

Montage Wand - Ceiling

Montage Türschwelle

Содержание TectoCell Compact 100

















Отзывы:

Похожие инструкции для TectoCell Compact 100