Viessmann B2SB Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 124

background image

14

■

The condensate pipe is connected to the discharge
pipe of the safety valve. The supplied condensate
hose meets the temperature requirements for CE
certification.

■

We recommend connecting the condensate pipe
internally to the domestic waste water system, either
directly or via a tundish.

■

If the condensate pipe is routed outside the building,
use a pipe with min.

7

30 mm and protect the pipe

from frost. Avoid long external pipe runs.

!

Please note

A frozen condensate pipe can result in faults
and damage to the boiler.
Always protect condensate pipes against frost.

■

Observe local building regulations.

Observe local waste water regulations.

Note

Fill the trap with water before commissioning.

Flue gas connection

Note

The "System certificate" and "Skoberne GmbH flue
system" labels enclosed with the technical documenta-
tion may only be used in conjunction with the
Viessmann flue system made by Skoberne.

Connecting the balanced flue pipe

Flue system installation instructions.

Connecting several Vitodens to a shared flue sys-
tem

If connecting several Vitodens to a shared flue system,
install a back draught safety device in each boiler.

■

Multiple vertical connections:
Back draught safety device available as separate
accessory

■

Flue gas cascade:
Back draught safety device in standard delivery for
the flue gas cascade (accessories)

Install the back draught safety device:

Back draught safety device installation instruc-
tions

Change control unit to operation with a shared flue
system:

■

In the commissioning assistant, select the

"Multiple

connections"

setting under

"Flue system"

.

or

■

Set parameter/code 7E:1 in the "General" group.

Do not carry out

commissioning

until the following

conditions are met:

■

Free passage through the flue gas pipes.

■

Flue system with positive pressure is gas-tight.

■

Inspection port covers checked for secure and tight
seating.

■

Apertures for ensuring sufficient combustion air sup-
ply are open and cannot be closed off.

■

Applicable regulations on installing and commission-
ing flue systems have been followed.

Danger

Leaking or blocked flue systems or an insuffi-
cient supply of combustion air cause life threat-
ening poisoning due to carbon monoxide in the
flue gas.
Ensure the flue system functions correctly. Aper-
tures for combustion air supply must not be able
to be closed off.
Prevent condensate drainage via a wind protec-
tor.

Installing the boiler

Condensate connection

(cont.)

5778741

Installation

«
...
12
13
14
15
16
...
»

Содержание B2SB





























































































































Отзывы:

Нет отзывов

Похожие инструкции для B2SB

Бренд: Calomax Страницы: 13

Бренд: U.S. Boiler Company Страницы: 180

Бренд: R&V Works Страницы: 12

Бренд: Zojirushi Страницы: 40

Бренд: Westen Страницы: 28

DynaFlame Series

Бренд: Camus Hydronics Страницы: 92

Бренд: UTICA BOILERS Страницы: 28

Бренд: UTICA BOILERS Страницы: 52

KEYSTONE STEAM II

Бренд: PENNCO Страницы: 20

Бренд: PENNCO Страницы: 32

Бренд: PENNCO Страницы: 44

Бренд: PENNCO Страницы: 64

Бренд: Enerzone Страницы: 24

Бренд: Nature's Comfort Страницы: 30

Бренд: Potterton Страницы: 8

PROFILE LPG 100e

Бренд: Potterton Страницы: 30

Hot-2-Go Series

Бренд: Hydro Tek Страницы: 20

Бренд: Worcester Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды