Viessmann B2SB Скачать руководство пользователя страница 18

Страница: 18 / 124

Connections to 230 V~ plugs

fÖ

Power supply

■

Power supply for accessories

■

External demand/blocking

Connections to LV plugs

Plug X3 can be removed to facilitate installation.

Outside temperature sensor

Flow temperature sensor for low loss header
(accessories)

KM-BUS connection, variable speed heating cir-
cuit pump (if installed)

X21 CO limiter (accessories)

aVG

KM-BUS subscriber (accessories)
To connect several accessories, see page 21.

■

Vitotrol 200-A or 300-A remote control unit

■

Vitocom 100, type GSM

■

Mixer extension kit

■

AM1 extension

■

EA1 extension

■

Wireless base station

■

KM-BUS distributor

Information on connecting accessories

When connecting accessories observe the sep-
arate installation instructions provided with
them.

Outside temperature sensor

Fitting location for outside temperature sensor

■

North or north-westerly wall, 2 to 2.5 m above
ground level; in multi storey buildings, in the upper
half of the second floor

■

Not above windows, doors or vents

■

Not immediately below balconies or gutters

■

Never render over.

Outside temperature sensor connection

2-core lead, length max. 35 m with a cross-section of
1.5 mm

Installing the boiler

Electrical connections

(cont.)

5778741

Installation

Содержание B2SB





























































































































Результаты поиска

Содержание B2SB

Отзывы:

Похожие инструкции для B2SB

Бренды по названию

Популярные бренды

Viessmann B2SB, Инструкции по установке и обслуживанию для подрядчиков

Результаты поиска

Содержание B2SB

Отзывы:

Похожие инструкции для B2SB

Бренды по названию

Популярные бренды