background image

136

Primary circuit return temperature sen-
sor......................................................86
Product information..............................6
Programming unit...............................85
Pt500..................................................87
Pumps................................................86

R

Removing the heat pump module......89
Removing the top panel.....................27
Removing the transport brackets.......26
Repairs...............................................84
Repair work........................................69
Reports............................................115
– Control parameters.......................116
Ripple control receiver...........57, 58, 60
Room height.......................................23

S

Safety connections.............................46
Safety valve.......................................28
Seal rings, replacing..........................71
Secondary circuit
– Filling..............................................71
Secondary circuit flow temperature sen-
sor......................................................86
Secondary circuit return temperature
sensor................................................86
Secondary pump
– Parameters.....................................76
Selecting the parameter group...........74
Sensor PCB.......................................49
Sensor resistance curves...................87
Sensors..............................................86
Sensors, checking..............................87
Service menu
– Calling up........................................74
– Disabling.........................................74
– Enabling..........................................74
Setting parameters.............................74
Signal connections.............................46
Siting......................................20, 23, 25
Solar air absorber..............................80

Solar thermal system
– Parameter settings.........................80
Specification
– Brine/water heat pumps................127
– Water/water heat pumps..............129
Standard tariff meter..............57, 58, 60
Structure-borne noise........................23
Swimming pool...................................53
System examples
– Legend..............................................8
System pressure check......................71
System schemes................................74

T

Temperature limiter............................38
Temperature sensor
– Curve, type Pt500A........................88
Temperature Sensor
– Curve, type NTC 10 kΩ..................88
Temperature sensor, hot gas.............87
Temperature sensor, suction gas......86
Temperature sensors...................1519
Terminating service............................74
Three phase monitor..........................62
Three-phase monitor..........................85
Tightness test.....................................71
Tilting angle........................................23
TNC system.....................57, 58, 60, 61
Top-up water......................................70
Total weight........................................23
Transport bracket...............................89

U

Underfloor heating.............................38
Underfloor heating circuit...................38

V

Ventilation..........................................81
Venting
– Primary side....................................70
– Secondary side...............................70
Vitocom..............................................77
Volume...............................................89

Keyword index

Keyword index

 (cont.)

5546 267 GB

Содержание 7514659













































































































































Отзывы: