Viessmann 7514659 Скачать руководство пользователя страница 23

Страница: 23 / 140

For handling purposes, the heat pump
module can be removed (see
page 89).

Please note

Prevent damage to the appliance
during handling.

Never

put weight on the top, front

or side panels of the appliance.

Please note

Tilting the compressor at a steep
angle inside the heat pump can
result in appliance damage.
Max. tilting angle 45 °

Installation room requirements

Please note

The installation room must be dry
and free from the risk of frost.
Ensure ambient temperatures
between 0 and 35 °C.

Please note

Avoid risks of explosion due to
dust, gases and vapours.
Avoid dust, gases and vapours in
the installation room.

Please note

Observe the permissible floor
load.
■ Align the appliance horizon-

tally.
If the adjustable feet are used
to compensate for an uneven
floor (max. 10 mm), the pres-
sure load on the feet must be
distributed evenly.

■ The total weight must be con-

sidered (see table).

Total weight
Type

Weight

BW 351.A18

312 kg

BWS 351.A18

307 kg

To prevent the transmission of structure-
borne noise, never site the appliance on
ceilings with wooden joists, e.g. in the
attic.

Minimum room volume (to EN 378)

Type

Minimum spa-
tial volume

BW 351.A18

24 m

BWS 351.A18

24 m

Preparing for installation

Siting conditions

5546 267 GB

Installation

Содержание 7514659













































































































































Результаты поиска

Содержание 7514659

Отзывы:

Похожие инструкции для 7514659

Бренды по названию

Популярные бренды

Viessmann 7514659, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 7514659

Отзывы:

Похожие инструкции для 7514659

Бренды по названию

Популярные бренды