manualshive.com logo in svg

Viega 8350.31, Инструкция по эксплуатации, Страница: 39 / 48

Поделиться
Скачать
Viega 8350.31 Скачать руководство пользователя страница 39

3.3

Commissioning

3.3.1

Setting the flush

Programming the control can be carried out for 30 minutes after the

supply voltage is applied. The control returns to normal operation after

30 minutes – programming is now blocked. If the settings have to be

changed after this time, the control must be disconnected from the

power supply for at least 10 seconds.

The programming set required to program the device is not

included in the scope of delivery. It can be purchased sepa‐

rately as accessory. 

Ä

 „Optional accessories“ on page 15

Observe the following features during programming:

–

Only one value can be set per programming step.

–

The settings are retained, even if there is an interruption

in the power supply.

–

The programming process can be cancelled without a

change of the settings by holding the magnetic key in

front of the programming contact until no acoustic signal

has sounded for more than two seconds.

Requirements:

n

The revision shaft is open and the control can be accessed.

n

The control programming block is not active.

n

The programming set is available.

Remove the protective cap of the programming connection from the

control.

Programming block

Setting the flush volume

Handling

WC flush actuation

39 from  48

Содержание 8350.31

















































Отзывы:

Нет отзывов