manualshive.com logo in svg

Viega 4914.11, Инструкция по эксплуатации, Страница: 24 / 26

Поделиться
Скачать
Viega 4914.11 Скачать руководство пользователя страница 24

3.2.4

Mounting the top

A top with the grate must still be mounted to finish off the mounting of
the drain. Proceed as follows:

If necessary, insert backflow seal in the lowest notch of the top.

INFO! The backflow seal be must employed when no damp-

ness is supposed to flow into the drain from outside of the

top but water may seep in from below. Normally, no backflow

seal is mounted so that water that occurs around the frame

(e. g. due to a leaky silicone joint) can flow away. A backflow

seal is mounted in the following cases: 

–

In the case of the risk of a build-up of water that can soak

through the screed. 

–

During the mounting of a stacking element for the bonded

sealing (see instructions for use of the stacking element). 

Calculate FFL and cut top flush to length.

Install plug-in adapter.

Insert top.

Calculate FFL and cut top flush to length.

Install plug-in adapter with backflow seal.

Insert top.

Drain in the bare floor

Drain in levelling screed or heat insulation

Handling

Advantix Top bathroom drain

24 from  26

Содержание 4914.11



























Отзывы:

Нет отзывов