Viega 4914.11 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 26

Viega 4914.11 Скачать руководство пользователя страница 15

3 Handling

3.1

Assembly information

3.1.1

Important note

Before assembly:

n

Check if the drainage capacity of the drain is sufficient for the arising
water volume

linktarget [Ablaufleistung] doesn't exist but @y.link.required='true'

.

n

Check if the installation height of the drain corresponds with the
planned floor construction.

n

Ensure that the required connection line is installed with the neces-
sary incline to the planned installation location.

n

If necessary, supply the required accessories

Ä

Chapter 2.5

„Required accessories“ on page 13.

During assembly:

n

Observe installation dimensions.

n

Decide whether or not a backflow seal is required in the insertion
part of the top.

After assembly:

n

The drain flange must be fully lined with mortar.

3.1.2

Installation dimensions

Fig. 8: Dimensional drawing model 4914.11

3.1.3

Tools and materials

n

if necessary, sealing collar, clamping ring, fitting screws

n

Top with grate, if not included in scope of delivery

n

if necessary, stacking element for bonded sealing model 4944

n

Material for securing the drain

Required material

Handling

Advantix Top bathroom drain

15 from 26

«
...
13
14
15
16
17
...
»

Содержание 4914.11



























Отзывы:

Нет отзывов