Victron energy Phoenix Smart IP43 12/30 страница 57 Скачать руководство пользователя | Manualshive

Страница: 57 / 59

background image

8.3. Power supply function

The Victron

Phoenix Smart IP43 Charger

range are also suitable for use as a DC power supply, to power equipment without a

battery connected (or while also connected to a battery).

While it’s still possible to use the charger as a power supply without changing any settings, a dedicated ‘Power supply’ mode
exists for this purpose/usage.

If the charger will be used as a power supply, it is recommended to activate ‘Power supply’ mode, as it will disable the internal
charge logic and provide a constant DC supply voltage.

To activate power supply mode:

a. Access the ‘settings’ menu by selecting the 'settings' icon (gear) in the top right corner.

b. Select the 'Function' dropdown arrow to expand the menu, then select ‘Power supply' mode.

c. ‘Power supply' mode will now be enabled; once activated the BULK, ABS, FLOAT and STORAGE LEDs will be illuminated.

d. If required, adjust the desired output voltage and/or the 'Maximum current' limit.

To return the charger back to normal use as a battery charger, access the 'settings' menu and in the ‘Function’ drop down menu
select ‘Charger’ mode again.

Phoenix Smart IP43 Charger

Page 55

Advanced Configuration

«
...
55
56
57
58
59
»

Содержание Phoenix Smart IP43 12/30




























































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix Smart IP43 12/30

Бренд: AA Portable Power Corp Страницы: 3

Бренд: T'nB Страницы: 18

Бренд: Naztech Страницы: 18

OE Elsafe ARC-H

Бренд: OE electrics Страницы: 2

Бренд: AlzaPower Страницы: 50

Бренд: Beyerdynamic Страницы: 36

Бренд: ULTIMATE SPEED Страницы: 162

PROTRXion M-24V60-TRX

Бренд: Inventus Power Страницы: 26

SOLIDGRIP PRO NST-16EU

Бренд: Pingi Страницы: 8

Бренд: ANSMANN Страницы: 70

Бренд: AddEnergie Страницы: 14

M-RK 344A4616P1

Бренд: Ericsson Страницы: 28

Бренд: Schloder Страницы: 17

Бренд: LTC Страницы: 19

Бренд: Motorola Страницы: 76

PMLN6394 Series

Бренд: Motorola Страницы: 28

Бренд: Motorola Страницы: 52

Бренд: Motorola Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды