Victron energy Phoenix Smart IP43 12/30 Скачать руководство пользователя

Страница: 46 / 59

7. Monitoring

7.1. LED indications

7.1.1. Operation states

The Phoenix Smart IP43 Charger has multiple LEDs that can be referenced to determine the current charge state and other
operational information.

Refer to the LED indications in the table below:

Charge state

LOW

BULK

ABS

FLOAT

STORAGE

ALARM

Charging disabled

Off

Blinking

Off

Bulk

Off

Illuminated

Off

Absorption

Off

Illuminated

Off

Recondition

Off

Blinking

Off

Float

Off

Illuminated

Off

Storage

Off

Illuminated

Off

Low current mode

Illuminated

N/A

7.1.2. Error states

If an error occurs, the red ALARM LED will illuminate, the charge state LEDs can then be referenced to determine the specific
error state.

Refer to the LED indications in the table below:

Error state

LOW

BULK

ABS

FLOAT

STORAGE

ALARM

Bulk time protection

Off

Blinking

Off

Illuminated

Internal Error

Off

Blinking

Off

Illuminated

Charger over-voltage

Off

Blinking

Off

Blinking

Illuminated

Charger over-current

Off

Blinking

Off

Blinking

Illuminated

Low mains voltage

Blinking

Off

Illuminated

BMS connection lost

Off

Blink

Illuminated

Phoenix Smart IP43 Charger

Page 44

Monitoring

Содержание Phoenix Smart IP43 12/30




























































Результаты поиска

Содержание Phoenix Smart IP43 12/30

Отзывы:

Похожие инструкции для Phoenix Smart IP43 12/30

Бренды по названию

Популярные бренды

Victron energy Phoenix Smart IP43 12/30, Руководство пользователя

Результаты поиска

Содержание Phoenix Smart IP43 12/30

Отзывы:

Похожие инструкции для Phoenix Smart IP43 12/30

Бренды по названию

Популярные бренды