Victron energy BlueSolar SCC010005000 Скачать руководство пользователя страница 41

Страница: 41 / 122

If the battery is connected with inverse polarity, the output polarity

will also inverse.

A 20A fuse should be inserted in the positive wire to the battery.

Connect the photovoltaic module to the charge regulator. If there is
sunshine, the charging indicator should turn on.

Connect the load to the charge controller; press the ON/OFF button to

start.

3. LED INDICATORS

Green LED is ON when solar is charging the battery.

In case of system over voltage the green LED blinks.

Green LED is ON when the battery voltage is in the right range.

Green LED is slowly flashing when the battery is fully charged.

Yellow LED is ON when the battery voltage is low.

Red LED is ON when the load is cut off.

In case of overload the red LED is slowly flashing

(The load current is 1.25 times of rated current for 60 seconds, or

the load current is 1.5 times of rated current for 5 seconds)

Red LED is fast flashing in case of short-circuits.

Red LED is ON when the push button is ON.
Red LED is OFF when the push button is OFF.

Содержание BlueSolar SCC010005000



























































































































Результаты поиска

Содержание BlueSolar SCC010005000

Отзывы:

Похожие инструкции для BlueSolar SCC010005000

Бренды по названию

Популярные бренды

Victron energy BlueSolar SCC010005000, Руководство пользователя

Результаты поиска

Содержание BlueSolar SCC010005000

Отзывы:

Похожие инструкции для BlueSolar SCC010005000

Бренды по названию

Популярные бренды