Victron energy BlueSolar SCC010005000 Скачать руководство пользователя страница 79

Страница: 79 / 122

5. Protection

Load Overload

If the load current exceeds the rated current of controller (

≥1.05 times

rated discharge current), the controller will disconnect the load.
Overloading must be cleared, then press the switch button.

Load Short Circuit

Fully protected against load wiring short-circuit (

≥2 times rated

discharge current). After one automatic load reconnect attempt, the
fault must be cleared by restarting the controller or pressing the switch
button.

PV Reverse Polarity

Full protection against PV reverse polarity, no damage to the
controller will result. Correct the wiring to resume normal operation.

Battery Reverse Polarity

Full protection against battery reverse polarity, no damage to the
controller will result. Correct the wiring to resume normal operation.

Damaged Temperature Sensor

If the temperature sensor short-circuited or damaged, the controller will
be charging or discharging at the default temperature (25°C).

Overheating Protection

If the temperature of the controller heat sink exceeds 85

C, the controller

will stop charging and discharging. When the temperature is below 75

the controller will restart.

High Voltage Transients

Limited internal transient protection.
In lightning prone areas, additional external suppression is
recommended.

Содержание BlueSolar SCC010005000



























































































































Результаты поиска

Содержание BlueSolar SCC010005000

Отзывы:

Похожие инструкции для BlueSolar SCC010005000

Бренды по названию

Популярные бренды

Victron energy BlueSolar SCC010005000, Руководство пользователя

Результаты поиска

Содержание BlueSolar SCC010005000

Отзывы:

Похожие инструкции для BlueSolar SCC010005000

Бренды по названию

Популярные бренды