Victory Motorcycles OCTANE 2017 Скачать руководство пользователя страница 62

Страница: 62 / 112

Maintenance

Fuel System

Fuel Tank Removal

9. Disconnect the fuel pump electrical

connector by depressing the release tab on
the connector body. Gently pull it free from
the fuel pump.

10. Wrap a shop towel around the fuel fitting.

11. Disconnect the fuel supply line connector

from the fuel pump by squeezing the release
tabs on both sides of the fitting.

12. Install the fuel tank fitting plug tool onto the

fuel pump fitting to protect the fitting and
prevent fuel from seeping out of the tank.

13. Lift the rear of the fuel tank and carefully

slide it rearward to release it from the front
isolators.

14. Lift the tank up and away from the frame.

Reinstall the front isolators if they become
dislodged.

15. Place the fuel tank on a flat surface in a

secure location.

Fuel Tank Installation

1. Place the handlebars in the straight ahead

position. Cover the front of the fuel tank with
a protective cloth to prevent damage.

2. Make sure the front isolators are installed to

the frame. Apply alcohol, soapy water or
rubber lubricant to the isolators and to the
sides of the air box seal to ease tank
installation.

3. Using care to avoid damage to the fuel tank

fitting and special tool, lower the fuel tank
onto the frame of the motorcycle. Slide the
tank forward to make sure it’s fully seated on
the isolators.

Step 11

Step 9

Step 13

Fuel Tank

Fitting Plug

Tool

Step 3

Содержание OCTANE 2017

















































































































Результаты поиска

Содержание OCTANE 2017

Отзывы:

Похожие инструкции для OCTANE 2017

Бренды по названию

Популярные бренды

Victory Motorcycles OCTANE 2017, Руководство пользователя для мотоциклиста

Результаты поиска

Содержание OCTANE 2017

Отзывы:

Похожие инструкции для OCTANE 2017

Бренды по названию

Популярные бренды