Victory Motorcycles OCTANE 2017 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 112

background image

59

Maintenance

Fuel System

CAUTION!

Always observe all fuel safety procedures when inspecting or servicing the fuel system.

See page 18.

Fuel Tank Removal

Before beginning, be prepared to place the fuel tank in a secure location to avoid scratching
the finish and to catch any fuel that may leak or drip from disconnected hoses or fittings.

Please read the entire removal and reinstallaton procedure
before beginning. Do not attempt to remove and install the
fuel tank if you’re not comfortable with this procedure. Your
authorized dealer can provide this service.

A special fuel tank fitting plug tool is required for this
procedure. Your VICTORY dealer can provide this tool.

1. Remove the seat. See page 76.

2. Remove the fuel tank filler pad to access the

fuel tank bolts.

3. Remove the four (4) rear fuel tank bracket bolts.

Set hardware aside for reassembly.

4. Locate the rubber elbow and the straight rubber

coupler exiting the rear of the tank mounting
bracket.

5. Gently pull the rubber elbow free of the tube to

disconnect the fuel tank vent line.

6. Gently pull the straight coupler free of the tube

to disconnect the fuel cap recess drain line.

7. Place the handlebars in the straight ahead

position. Cover the front of the fuel tank with a
protective cloth to prevent contact with the
instrument cluster, which could cause damage.

8. Lift and support the rear of the tank

approximately two inches (5 cm).

Fuel Tank

Fitting Plug

Tool

Step 3

Step 5

Step 6

California Models

Step 5

Step 6

«
...
59
60
61
62
63
...
»

Содержание OCTANE 2017

















































































































Отзывы:

Нет отзывов

Похожие инструкции для OCTANE 2017

Бренд: PACIFIC CYCLE Страницы: 112

Бренд: BMW Страницы: 288

Бренд: kellermann Страницы: 2

Бренд: BMW Motorrad Страницы: 146

Бренд: Suzuki Страницы: 311

Бренд: rizoma Страницы: 10

Бренд: TB Страницы: 8

Бренд: GAS GAS Страницы: 150

Fastway PMB-01-5203

Бренд: Pro Moto Billet Страницы: 2

Бренд: Yamaha Страницы: 74

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды