Victory Motorcycles OCTANE 2017 Скачать руководство пользователя | Manualshive

Страница: 74 / 112

background image

72

Maintenance

Steering Head Inspection

1. Elevate and support the motorcycle with the front tire slightly off the floor. See page 53.

CAUTION!

Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips

or falls.

2. Turn the handlebars from stop to stop. The action should be smooth but not loose. Make

sure wires, hoses and control cables do not interfere with smooth steering.

3. Position the front wheel straight ahead. Grasp the front forks near the front axle and

attempt to move the wheel front-to-back. If there is front-to-back movement at the
steering head, see your dealer or other qualified person for service.

4. If steering binds, feels rough or uneven, or if movement is detected at the steering stem,

see your dealer or other qualified person for service.

5. Rotate the front wheel and inspect for smooth rotation of front wheel bearings. If

roughness or unusual sounds are present, see your dealer or other qualified person for
service.

6. Turn handle bars full right or left and hold against the fork stop. Attempt to move front

wheel side-to-side. If movement is observed, see your dealer or other qualified person
for service.

Crankcase Breather Hoses

Inspect the crankcase breather (vent) hoses
each time the fuel tank is removed to
perform air filter service or other
maintenance. Inspect both breather hoses
along their length and at both ends. Make
sure hoses are not restricted, kinked, cracked
or otherwise damaged. Replace any worn or
damaged hoses.

Exhaust System

Check the exhaust system for stains from leaking exhaust gasses. Replace damaged or
leaking exhaust gaskets. Check all exhaust system fasteners. Tighten loose clamps and
fasteners. Do not overtighten. For more information, see the

VICTORY Service Manual.

Your

authorized VICTORY dealer can assist.

Sidestand Lubrication

Periodically lubricate the sidestand bushing. See page 43 for sidestand inspections.

Breather Hoses

«
...
72
73
74
75
76
...
»

Содержание OCTANE 2017

















































































































Отзывы:

Нет отзывов

Похожие инструкции для OCTANE 2017

Бренд: oset Страницы: 20

Бренд: Kask Страницы: 68

Бренд: Suzuki Страницы: 440

Бренд: Termignoni Страницы: 9

Бренд: Crivit Страницы: 58

California EV V1100

Бренд: MOTO GUZZI Страницы: 173

Бренд: Honda Страницы: 127

Бренд: Yamaha Страницы: 118

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 106

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 134

Бренд: Yamaha Страницы: 116

Бренд: Malaguti Страницы: 383

Бренд: GAS GAS Страницы: 52

TXT RACING 2015

Бренд: GAS GAS Страницы: 59

Бренд: GAS GAS Страницы: 56

Бренд: GAS GAS Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды