Victaulic VG412 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 46

background image

VG412

19

7. Tighten clamp screws on the pipe evenly and with sufficient force to resist rotation of the pipe during

cut off and grooving. NOTE: Check the tightness of the clamp screws throughout the cutting and
grooving operation, and retighten if necessary

8. Attach the motor mounting bracket to the rear or the frame.

Figure 19

9. Attach the motor to the bracket, with the wing screws, but do not tighten. Align the hex in the drive

socket with the hex on the drive shaft by turning the chuck by hand and slide the socket over the drive
hex. Tighten the chuck and tighten the mounting wing screws securely.

Figure 20

«
...
18
19
20
21
22
...
»

Содержание VG412















































Отзывы:

Нет отзывов

Похожие инструкции для VG412

Бренд: Samson Страницы: 16

Бренд: Veit Страницы: 70

Бренд: Gage Bilt Страницы: 24

Бренд: Gage Bilt Страницы: 24

Бренд: Gage Bilt Страницы: 24

Бренд: Freeman Страницы: 19

Бренд: SilverBolt Страницы: 9

Бренд: Wacker Neuson Страницы: 32

Бренд: Park Tool Страницы: 2

Бренд: Draper Страницы: 12

Бренд: Oemtools Страницы: 4

Бренд: Magnetic Instrumentation Страницы: 27

Бренд: Daewoo Страницы: 19

Бренд: Rosenberger Страницы: 16

Бренд: Ribimex Страницы: 19

Бренд: Marshalltown Страницы: 32

Бренд: Facom Страницы: 4

Бренд: Prebena Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды