Victaulic RG1210 Скачать руководство пользователя страница 23

Страница: 23 / 24

MD_DoI_RGT_008_051220_en.docx

EC DECLARATION OF INCORPORATION

In Accordance with the Machinery Directive 2006/42/EC

Victaulic Company, headquartered at 4901 Kesslersville Road, Easton, PA 18040, USA, hereby declares

that the machinery listed below complies with the essential safety requirements of the Machinery

Directive, 2006/42/EC.

Product Model:

RG1200, RG1210

Serial No. :

Refer to Machinery Nameplate

Product Description:

Portable roll grooving tool

Conformity Assessment:

2006/42/EC, Annex I

Technical Documentation:

The relevant technical documentation prepared in

accordance with Annex VII (B) of the Machinery Directive

2006/42/EC, will be made available upon request to the

governing authorities.

Compatible Power Drives:

When installed with the following power drive unit,

having an appropriate EC Declaration of Conformity in

accordance with Annex II (A) of the Directive

2006/42/EC, the RG1200 and RG1210 models listed

above may be commissioned for the full intended

purpose:

Ridgid 300

Authorized Representative:

Victaulic Company

c/o Victaulic Europe BVBA

Prijkelstraat 36

9810, Nazareth

Belgium

Signed for and on behalf of Victaulic Company,

Mr. Len R. Swantek

Director – Global Regulatory Compliance

Machinery Manufacturer Representative

Place of Issue: Easton, Pennsylvania, USA

Date of Issue: May 12, 2020

Содержание RG1210

























Результаты поиска

Содержание RG1210

Отзывы:

Похожие инструкции для RG1210

Бренды по названию

Популярные бренды

Victaulic RG1210, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание RG1210

Отзывы:

Похожие инструкции для RG1210

Бренды по названию

Популярные бренды