manualshive.com logo in svg

VibroSystM DMV-100, Руководство по установке

Поделиться
Скачать
VibroSystM DMV-100 Скачать руководство пользователя страница 3

 

3

DMV-100 Rotor Creep and Speed Detector - Installation Manual

TABLE OF CONTENTS

1.

OVERVIEW OF THE DMV-100 ROTOR CREEP AND SPEED DETECTION SYSTEM

2.

INSTALLATION OF THE VM 3.12 AIR GAP SENSOR FOR MOVEMENT DETECTION

2.1

Preliminary considerations ....................................................................................................................  7
2.1.1

Supplies needed ........................................................................................................................  8

2.2

Positioning the air gap sensor................................................................................................................  8

2.3

Step by step installation of the VM 3.12 Sensor ...................................................................................  9
2.3.1

Preparation of Stator Surface....................................................................................................  9

2.3.2

Glueing the VM 3.12 Sensor ....................................................................................................  9

2.4

VM 3.12 Sensor - General specifications..............................................................................................  11

3.

INSTALLATION OF THE TRIAXIAL EXTENSION CABLE

3.1

Preliminary considerations ....................................................................................................................  13
3.1.1

Supplies needed ........................................................................................................................  14

3.1.2

Tools needed.............................................................................................................................  14

3.2

Step by step installation of the triaxial extension cable.........................................................................  14
3.2.1

On site preparation ...................................................................................................................  14

3.2.2

Installation of triaxial extension cable - sensor end .................................................................  

15

3.2.3

Silicone application ..................................................................................................................  20

3.2.4

Installation of triaxial extension cable - signal conditioning module end................................  

21

3.3

General specifications of the triaxial extension cables..........................................................................  22

4.

INSTALLATION OF THE DCC-631 MODULE FOR THE DMV-100 SYSTEM

4.1

Preliminary considerations ....................................................................................................................  23

4.2

Installation of the DCC-631 module .....................................................................................................  24
4.2.1

Supplies needed ........................................................................................................................  24

4.2.2

Tools needed.............................................................................................................................  24

4.2.3

Mechanical installation of the casing .......................................................................................  24

4.3

Connecting the cable to the DCC-631...................................................................................................  25

4.4

LED functionality ..................................................................................................................................  26

4.5

DCC-631 Signal Conditioning Module - General specifications..........................................................  

27

5.

INSTALLATION OF THE DMV-100 UNIT

5.1

General description of the DMV-100 Unit............................................................................................  29
5.1.1

Overview of the DMV-100 Unit main components .................................................................  30

5.2

Installation of the DMV-100 Unit in a 19” rack or cabinet...................................................................  33
5.2.1

Preliminary considerations for installation in a 19” rack or cabinet ........................................  

33

5.2.2

Required tools and supplies......................................................................................................  33

5.2.3

Fixing the DVM-100 unit to the rack .......................................................................................  34

5.3

Cabling the DMV-100 Unit...................................................................................................................  35

Содержание DMV-100





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды