VibroSystM DMV-100 Скачать руководство пользователя страница 11

Страница: 11 / 52

DMV-100 Rotor Creep and Speed Detector - Installation Manual

2.4 VM 3.12 Sensor - General specifications

Operation

•

Linear measuring range with

DCC-631-10S-5/50-ala2/p

5 to 50 mm

[197 to 1968 mils]

LIN-331-10J-2/20

2 to 20 mm

[79 to 787 mils]

LIN-331-10J-5/35

5 to 35 mm

[197 to 1378 mils]

LIN-331-10S-2/20

2 to 20 mm

[79 to 787 mils]

LIN-331-10S-5/35

5 to 35 mm

[197 to 1378 mils]

LIN-331-15Q-2/20

2 to 20 mm

[79 to 787 mils]

•

Frequency response

limited by the linearization module

•

Interchangeability

± 5 %

Connection

•

Integral cable

- Type

coaxial

- Length

50.0 cm

[19.68 in.]

- Connector

SMA plug (male contact)

Environmental

•

Temperature range

- Operation:

to 125

[32

to 257

- Storage:

to 125

[32

to 257

•

Magnetic field

up to 2 Tesla (50 Hz or 60 Hz)

•

Dust and oil contamination

films have no effect on performance

•

Humidity

up to 95%, non condensing

Physical characteristics

•

Dimensions

- Height (sensing surface only)

220.5 mm

[8.68 in.]

- Width

33.25 mm

[1.30 in.]

- Thickness

1.77 mm

[0.07 in.]

- Connector assembly diameter

7.92 mm

[0.312 in.]

Содержание DMV-100





















































Результаты поиска

Содержание DMV-100

Отзывы:

Бренды по названию

Популярные бренды

VibroSystM DMV-100, Руководство по установке

Результаты поиска

Содержание DMV-100

Отзывы:

Бренды по названию

Популярные бренды