manualshive.com logo in svg

VibroSystM DMV-100, Руководство по установке

Поделиться
Скачать
VibroSystM DMV-100 Скачать руководство пользователя страница 31

Speed Display Unit and Keypad

31

DMV-100 Rotor Creep and Speed Detector - Installation Manual

The five-digit display unit shows machine 
speed over a programmed range.

Figure 28 : Speed Display unit

A field setup procedure is required prior to operation. The user must enter design-specific information such 
as the number of poles. The five button keypad allows browsing through display and configuration param-
eters. On-screen keywords guide users during setup (refer to 

5.4 “Initial setup of the DMV-100 System”

).

4

5

6

9

7

10

8

Figure 29 : 

4-20 mA Output (RPM) Terminals

Back panel of the DMV-100 rack-mount unit

This 3-position connector delivers an analog output signal proportional to the actual RPM speed.

Relay Output (Creep) Terminals

This 3-position connector gives access to the DMV-100 internal relay. The DMV-100 internal relay can be 
used by annunciation devices located on remote field equipment.

Note: Refer to the DMV-100 datasheet for load capacity.

3

4

5

Содержание DMV-100





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды