11
3.2
Version 10, 12, 15 links automatics HONEYWELL, valve HONEYWELL
3.2.1
Installation of the Distributing Box
List of parts needed
1 pc
Switch box
1 pc
Installation Console (large)
1 pc
Installation Console (small)
16 pcs
Screw AM5x8mm
16 pcs
Rosette washer Ø 5,2mm
1 pc
Cover plate HONEYWELL
2 pcs
Rubber bushing Ø 13 mm
2 pcs
Entry bushing PG 9
10 pcs
Entry Bushing PG11
1 pc
Fuse box
1 pc
Tube fuse 4A
1 pc
End piece of the tube PG 48
1 pc
Nut of the end piece of the tube PG 48
600 mm
Protection tube PG 48
1 pc
End piece of the tube PG 36
1 pc
Nut of the end piece of the tube PG 36
450 mm
Protection tube PG 36
1 pc
Ionization automatics HONEYWELL
S 4563B1011
2 pcs
Screw AM4 x 8
1 pc
Bundle of conduits
Installation procedure
1.
With aid of 8 screws M5 with rosette washers, the installation console is to be mounted on a side portion of the jacket left cover B. Above,
a smaller console shall be installed to assist in securing the terminals
2.
Sequentially, 8 pc of entry bushing PG11,to be mounted on the distribution box. Then, 8 pc of entry bushings PG9, end pieces of cover
tubes PG39 a PG48, a fuse box with 4A fuse, and two screws M5 are used to secure the cover HONEYWELL, containing already installed
from left two bushings PG9 and two rubber bushings Ø 13 mm.
3.
The box so equipped is to be mounted on a side part B left using four screws M5.
4.
At the box’s bottom on left, using two M4 screws, the ionization automatics HONEYWELL is to be fastened such, that the connector
leading to the igniter is orientated right down.
5.
The terminal X10 with conduits and suppression component Z1 is fastened into the lower portion of the installation console (Large) Anti-
jamming element is to be fastened using the fastener band to the console.
6.
Following the schematics, line wires 1, 2 are connected to the fuse box
7.
Further line wires No.10,11,15,22,,27,28,45 and 55 are connected to the ionization automatics.
8.
The remaining line wires put through the end piece of the protective tube PG48, and then the actual tube is inserted over the conductors
9.
Line wire 90, connected to the igniting electrode, is to be inserted through the rubber bushing Ø 13.
10. Conduit no. 90, connected to the guardian electrode, is to be inserted through the rubber bushing Ø 13.
11. Conduit no. 92 to burner is to be iserted through bushing PG9.
12. Cable W1 is to be inserted through the last bushing PG9 and its conduits are to be connected in the distributing box as follows:
Black
J3: 2
Brown
X10: 23
Grey
X10: 24
Blue
X10: 5
Green-yellow
Terminal plate console
13. The cable W1 opposite end is to be connected to X6 gas valve connection outlet as follows:
Black
X6: L1
Brown
X6: L2
Grey
X6: L3
Blue
X6: N
Green-yellow
PE
14. The outlet X6 before covering is to be affixed using two self-cutting screws 2,9x19 onto a side piece under the distributing box. Cover it
after its affixing.
15. Into the X6* gas valve connector are to be connected gas valve Y1 – X8.1 outlet cables.
16. (small 1
st
step) and X8.2 (High-Low coil) as follows:
X8.1 – Green – Yellow
X6*: PE
Blue
X6*: N
Brown
6*: L2
Black
X6*: L1
X8.2 – Green – Yellow
X6*: PE
Blue
X6*: N
Brown
X6*: L3
17. Similarly are to be connected cable conduits of the Gas valve Y2 – X9.1 (1st step) and X9.2 (High-Low coil).
3.2.2
Electrical Panel installation
List of parts needed
1 pc
Power module preconnected
1 pc
End piece of the tube PG 48
1 pc
Nut of the end piece of the tube PG 48
1 pc
End piece of the tube PG 36
1 pc
Nut of the end piece of the tube PG 36
Installation procedure
1.
End pieces of the tubes PG36 and PG48 are to be fastened into the electrical panel console
2.
Wires are to be put through the end piece PG48, and the cover tube secured
3.
Following the connection schematics, instruments are to be connected within the power network module:
BT2 – c.n.. 13,14,18,56
BT1 – c.n. 15,17,18,57
BT4 – c.n. 7,8,58
S1 - c.n. 2,3
H1 - c.n. 40
