VETRON 5000 Скачать руководство пользователя страница 46

Страница: 46 / 83

07/2020

VETRON 5000/5100 - FLAT BED MACHINE - INSTRUCTION BOOK

NR. PARAMETER

DESCRIPTION

THREAD TENSION

ADVICE!

Thread tension

The thread tension on conventional machines is adjusted with a spring. The reproduction of the desired thread

tension is difficult. The VETRON sets the thread tension with a step motor. The task of the tension spring is taken

over by a elastomer. A second thread tension on conventional machines needs an additional tension unit.

The VETRON accomplish the 2

thread tension by increasing the tension.

030

Thread tension A 1

Main thread tension in program.

Setting range 0 to 100 %.

031

Thread tension A 2

Higher thread tension than the main program.

Setting range 0 to 100 %.
The connection with the higher thread tension can be done by pushing button

or when the 2

top feed stroke is activated.

032

Thread tension B 1

(Two needle machine)

Main thread tension in program.

Setting range 0 to 100 %.

033

Thread tension B 2

(Two needle machine)

Higher thread tension than the main program.

Setting range 0 to 100 %.

The connection with the higher thread tension can be done by pushing button

or when the 2

top feed stroke is activated.

034

Thread tension level increase / decrease

based on material thickness

Two function are available.
Function 1 =

OFF

(no change on different material thickness)

Function 2 =

(lower percentage = less thread tension increase)

(higher percentage = more thread tension increase)

Automatic thread tension adjustment depends on material thickness

The tension will be adjusted with the information received from the material

thickness recognition. You can activate this function with the parameter

034

With a lower percentage the increase will be less than with a higher percentage.

05. PROGRAMMING

04.

PROGRAM PARAMETER

-3-14

Содержание 5000




















































































Результаты поиска

Содержание 5000

Отзывы:

Похожие инструкции для 5000

Бренды по названию

Популярные бренды

VETRON 5000, Инструкция по эксплуатации

Результаты поиска

Содержание 5000

Отзывы:

Похожие инструкции для 5000

Бренды по названию

Популярные бренды