VETRON 5000 Скачать руководство пользователя страница 28

Страница: 28 / 83

07/2020

VETRON 5000/5100 - FLAT BED MACHINE - INSTRUCTION BOOK

03. OPERATION OF THE MACHINE

01.01.

INSERTING THE NEEDLE (2- NEEDLE)

-2-2

CAUTION! RISK OF INJURY!

Push the X-button at the machine head, the red light illuminates showing the active

“BLOCKED MODE“

, or turn the machine off before inserting the needles. Failure to

comply produces a risk of injury in case of an unintentional machine operation.

INFO

Only use needles from the system intended for the machine.
(Needle system 134-35)

01. Push the X-button at the machine head, the red light illuminates showing

the active

“BLOCKED MODE”

, or turn the machine off.

02. Loosen the screws

03. Push the needles

fully in until they stop. Make sure that the groove

of the right needle points to the right and the left needle to the left.

04. Tighten the screws

again.

05. Push the X-button or switch the machine on again and follow the instructions

displayed on the control panel.

NOTE:

Before activating the machine by the X-button make sure to remove

sewing material

other items

below the sewing feet if necessary and

follow the instructions displayed on the control panel.

Содержание 5000




















































































Результаты поиска

Содержание 5000

Отзывы:

Похожие инструкции для 5000

Бренды по названию

Популярные бренды

VETRON 5000, Инструкция по эксплуатации

Результаты поиска

Содержание 5000

Отзывы:

Похожие инструкции для 5000

Бренды по названию

Популярные бренды