17
21
22
26
29
23
CURVE SELECT SW
○
a
○
a
○
b
○
c
○
c
L
L
E
E
V
POSITION
POSITION
POSITION
C.F.
CURVE
○
b
-6-
SA
!7
SA
Thi
sam
Mo
(be
cro
effe
!8
DE
It is
(0.5
TA
Th
late
!9
FIN
It i
(0m
r
CROSSFADER REVERSE SWITCH
This switch reverses the action of the crossfader
by switching PGM1 and 2.
t
PGM EFFECT (program effect) SWITCH
It is the switch which sends the signal of each
PGM channel to built-in sampler / delay. If it is
pushed, a signal will be sent to sampler / delay
section, and PGM EFFECT indicator will light up.
y
PGM EFFECT INDICATOR
The light will be switched on if PGM EFFECT
SWITCH of each PGM channel is pushed.
u
POWER INDICATOR
It is the indicator which tells power is supplyed.
Please confirm that this indicator is ON before use.
i
MASTER LEVEL
It is the volume which adjusts the level of the signal
outputted from OUTPUT JACK of a rear panel.
o
CF CURVE VOLUME
It is the volume which sets up the curve property
of a C.F.CURVE (crossfader curve).
(a)Curve for a long mix
If CROSSFADER volume is moved, the
volume level changes gently with PGM-1 and
PGM-2 signal interchanging each other.
(b)It is the middle curve of (a) and (c)
(c)Curve for scratch performance
The volume of CROSSFADER rise up most
rapidly.
!0
INPUT SELECT SWITCH
This switch is used to select the input (LINE or
PHONO) to be sent to each PGM channel. The
upper most position will select PHONO input.
This selector switch can also be used to perform
for TRANSFORMER SCRATCH. The operation
direction of this switch is selectable. To change
the operational direction of this switch remove,
the top panel and make the necessary the top
panel.
!1
INPUT FADER (PGM1/PGM2)
This fader is used to adjust the input level of
each PGM channel. The input fader curve can
be changed using a switch located on the unit
itself. This fader is a detachable for making
easy replacement. Ensure that you replace with
an IF-05PCV when it will worn out. For more
comprehensive instructions please refer to the
"HOW TO CHANGE THE FADER UNIT" section
of this user guide.
!2
INPUT LEVEL METER
The LED level meters indicate the signal level of
each PGM channel.
!3
CROSSFADER
When the input level of PGM1 and PGM2 are
properly set, PGM1 will be heard with the
crossfader set to the left side. PGM2 will be
heard with the cross fader set to the right side.
When the crossfader is set in the center, both
programs will be heard. This is detachable fader
for the easy replacement with "CF-PCV" when it
is worn out. It is the switch which chooses the
signal (PHONO and LINE) inputted into each
PGM channel.
!4
MONITOR LEVEL
It is the fader which adjusts the volume of the
headphone connected to PHONES jack.
!5
C.F.MONITOR FADER
5
It is the fader which chooses the signal
monitored by headphone. Depends on the
position of a knob, the signal balance of PGM-1
and PGM-2 changes like CROSSFADER.
!6
MONITOR SELECT SWITCH
It is the switch which changes the monitor form
of headphone.
MASTER/EFFECT CUE
When a EFFECT
CUE switch is OFF, it can act as the monitor of
the signal outputted from LINE OUT jack
.Moreover, when a EFFECT CUE switch is ON,
it can act as the monitor only for of the signal
outputted from built-in sampler / delay.
CUE
It can act as the monitor of the signal of
PGM-1 or PGM-2 chosen by C.F.MONITOR
fader. When C.F MONITOR fader is set up in the
center position, you can monitor the signal of
both PGM-1 and PGM-2.
No
Wh
up
No
Wh
up
Notes
Even if C.F.REVERSE switch is set to the
"REVERSE" side, C.F.MONITOR volume is not
REVERSE(ed).
PMC05ProSL-E 04.7.13 11:22 AM ページ 7
