VESPA LX Series Скачать руководство пользователя страница 193

Страница: 193 / 272

Refitting

CAUTION

USE NEW ROLLER CASINGS, PIN, SEALING RINGS AND DUST GUARDS FOR REFITTING.

When fitting the fork, lubricate with the steering

bearing tracks with the recommended grease.

Tighten the lower ring nut

"A"

and the upper ring

nut

"B"

to the specified torque

Recommended products

AGIP GREASE PV2

Grease for the steering

bearings, pin seats and swinging arm

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 C

and +120 C; NLGI 2; ISO-L-XBCIB2.

Locking torques (N*m)

Lower steering ring nut

8 to 10

Upper steering

ring nut

35 to 40

Front shock absorber

Vespa LX 125 - 150 i.e.

Suspensions

SUSP - 193

Содержание LX Series

















































































































































































































































































Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды

VESPA LX Series, Руководство пользователя

Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды