VESPA LX Series Скачать руководство пользователя страница 125

Страница: 125 / 272

- Check there is no wear on the cam shaft retaining

plate and its associated groove on the cam shaft.

- If any of the above dimensions are outside the

specified limits, or there are signs of excessive

wear, replace the defective components with new

ones.

Characteristic

Maximum axial clearance admitted

0.42 mm

- Check there are no signs of wear on the auto-

matic valve-lifter cam, or the end-of stroke roller,

or the rubber buffer on the automatic valve-lifter

retaining cover.

- Check that the valve lifting spring has not yielded.

- Replace any defective or worn components.

- Check there are no signs of scoring or wear on

the rocking lever bolt.

Check there are no signs of wear on the pad from

contact with the cam and on the jointed adjustment

plate.

- Measure the internal diameter of each rocking

lever.

-Check that the elastic washer dedicated to the

axle clearance of the rocking levers is not worn. -

In case of anomalies, replace the damaged com-

ponents.

Characteristic

Minimum diameter permitted

Ø 11.970 mm

Maximum diameter admitted

Ø 12.030 mm

Refitting the head and timing system components

- Fit the timing chain guide slider.

- Insert the head and cylinder alignment dowels, fit the head gasket and the head on the cylinder.

Vespa LX 125 - 150 i.e.

Engine

ENG - 125

Содержание LX Series

















































































































































































































































































Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды

VESPA LX Series, Руководство пользователя

Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды