VESPA LX Series Скачать руководство пользователя страница 151

Страница: 151 / 272

7. When washing the vehicle, be careful with the electric components and wiring.

8. When an ignition problem is detected, start the checks from the battery and the injection system

connections.

9. Before disconnecting the MIU ECU connector, perform the following steps in the order shown:

- Set the switch to «OFF»

- Disconnect the battery

Failure to respect this norm may damage the control unit.

10. Do not invert the poles when fitting the battery.

11. To avoid causing any damage, disconnect and reconnect the MIU system connectors only if re-

quired. Before reconnecting, check that the connectors are dry.

12. When carrying out electric inspections, do not force the tester probes into the connectors. Do not

take measurements not specifically foreseen by the manual.

13. At the end of every check performed with the diagnostic tester, remember to protect the system

connector with its cap. Failure to observe this precaution may damage the MIU control unit.

14. Before reconnecting the quick couplers of the power supply system, check that the terminals are

perfectly clean.

Terminals setup

1. Injection warning light

2. incomplete

3. incomplete

(-)

lambda probe

(+)

live battery

(+)

battery

7. Immobilizer aerial

8. incomplete

Vespa LX 125 - 150 i.e.

Injection

INJEC - 151

Содержание LX Series

















































































































































































































































































Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды

VESPA LX Series, Руководство пользователя

Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды