VESPA LX Series Скачать руководство пользователя страница 131

Страница: 131 / 272

- Check the radial clearance on the connecting rod.

-Check the surfaces that limit the axial free-play

are not scored and measure the width of the crank-

shaft between these surfaces, as shown in the

diagram.

CAUTION

BE CAREFUL NOT TO LET THE MEASUREMENT BE AF-
FECTED BY THE UNIONS WITH THE CRANKSHAFT ENDS.

Characteristic

Standard clearance

0.036 to 0.054 mm

- If the axial clearance between crankshaft and

crankcase is exceeding and the crankshaft does

not have any defect, the problem must be due to

either excessive wear or wrong machining on the

crankcase.

CAUTION

THE CRANKSHAFT CAN BE REUSED WHEN THE WIDTH
IS WITHIN THE STANDARD VALUES AND THE SURFACES
SHOW NO SIGNS OF SCORING.

Characteristic

Distance between the shoulders

55.67 to 55.85 mm

- Check the diameters of both the bearings of the crankshaft in accordance with the axes and surfaces

shown in the figure. The half-shafts are classified in two categories Cat. 1 and Cat. 2 as shown the chart

below.

STANDARD DIAMETER

Specification

Desc./Quantity

Category 1

28.998 to 29.004

Category 2

28.004 to 29.010

Vespa LX 125 - 150 i.e.

Engine

ENG - 131

Содержание LX Series

















































































































































































































































































Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды

VESPA LX Series, Руководство пользователя

Результаты поиска

Содержание LX Series

Отзывы:

Бренды по названию

Популярные бренды