manualshive.com logo in svg

VESPA LX Series, Руководство пользователя

Поделиться
Скачать
VESPA LX Series Скачать руководство пользователя страница 117

- Measure the outside diameter of the piston, per-

pendicular to the gudgeon pin axis.

- Measure 36.5 mm from the piston crown's shown

in the figure.

N.B.

THE PIN HOUSINGS HAVE 2 LUBRICATION CHANNELS.
FOR THIS REASON MEASUREMENT OF THE DIAMETER
MUST BE CARRIED OUT ACCORDING TO THE AXIS OF
THE PISTON.

- Using a bore meter, measure the inner cylinder

diameter at three different points according to the

directions shown in the figure.

- Check that the coupling surface with the head is

not worn or misshapen.

- Pistons and cylinders are classified into catego-

ries based on their diameter. The coupling is car-

ried out in pairs (A-A, B-B, C-C, D-D).

Characteristic

Maximum allowable run-out:

0.05 mm

- The cylinder rectifying operation should be car-

ried out with a surfacing that respects the original

angle.

- The cylinder surface roughness should be 0.9

micron.

- This is indispensable for a good seating of the

sealing rings, which in turn minimises oil consump-

tion and guarantees optimum performance.

- The pistons are oversized due to cylinder rectifi-

cation and are subdivided into three categories

1st, 2nd, 3rd with 0.2-0.4-0.6 mm oversize. They

are also classified into 4 categories A-A, B-B, C-

C, D-D.

Inspecting the piston

- Carefully clean the sealing ring housings.

- Measure the coupling clearance between the sealing rings and the piston grooves using suitable

sensors, as shown in the diagram.

- If the clearance is greater than that indicated in the table, replace the piston.

Vespa LX 125 - 150 i.e.

Engine

ENG - 117

Содержание LX Series

















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды