Vertiv Liebert Mini-Mate MT036 страница 41 Скачать руководство пользователя

Страница: 41 / 80

EC-fan Low-voltage Tests

•

Check control input at the control-system connection (E1 and GND). Confirm that

there is a control voltage present at the connection.

NOTE: Use the GND in the connector. Do not connect the control ground to the PE in Main connector!

•

Check +10 V output on control-system connection (b10 V and GND).

EC-fan Alarm Contact Tests

Check the alarm contact at the alarm-relay connection to determine if there are any fault conditions

present.

Condition

No Fault Condition

Fault Condition

NC - COM

Closed

Open

NOTE: The table refers to conditions while the motor is actively energized. When the motor is de-

energized, it will be in a fault condition.

•

Check EC Control to determine the fault condition.

9.3 Direct-drive Blower System

Monthly inspection of the blower package includes: motor mounts, fan bearings, and impellers.

9.3.1 Fan Impellers and Motor Bearings Maintenance

Fan impellers should be periodically inspected and any debris removed. Check to see if they are tightly-

mounted on the fan shaft. Rotate the impellers and make sure they do not rub against the fan housing.

Although the motor bearings are permanently-sealed and self-lubricating, inspect the bearings monthly

for signs of wear.

9.4 Steam-generating Humidifier Maintenance

The humidifier drains and refills to maintain a current setpoint and alert the operator when the humidifier

canister needs to be replaced.

WARNING! Arc flash and electric shock hazard. Open all local and remote electric power-supply

disconnect switches, verify with a voltmeter that power is Off and wear appropriate,

OSHA-approved personal protective equipment (PPE) per NFPA 70E before working within the

electric control enclosure. Failure to comply can cause serious injury or death. Customer must

provide earth ground to unit, per NEC, CEC and local codes, as applicable. Before proceeding

with installation, read all instructions, verify that all the parts are included and check the

nameplate to be sure the voltage matches available utility power. The Liebert® controller does

not isolate power from the unit, even in the “Unit Off” mode. Some internal components require

and receive power even during the “Unit Off” mode of the controller. The only way to ensure

that there is NO voltage inside the unit is to install and open a remote disconnect switch. Refer

to unit electrical schematic. Follow all local codes.

WARNING! Risk of improper wiring, piping, moving, lifting and handling. Can cause equipment

damage, serious injury or death. Installation and service of this equipment should be done only

by qualified personnel who have been specially-trained in the installation of air-conditioning

equipment and who are wearing appropriate, OSHA-approved PPE.

9 Maintenance

Содержание Liebert Mini-Mate MT036

















































































Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды

Vertiv Liebert Mini-Mate MT036, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды