Vertiv Liebert Mini-Mate MT036 страница 24 Скачать руководство пользователя

Страница: 24 / 80

Document Number

Title

Unit-to-Unit Networking

DPN004840

3-ton Model iCOM unit-to-unit field connection

DPN004841

4- and 5-ton Models iCOM unit-to-unit field connection

Table 5.1 Electrical Field-connection Drawings (continued)

5.1 Low-voltage Electrical Field Connections

Figure 5.1 on the facing page, shows an overview of the low-voltage wiring connections between the

Mini-Mate module and the condensing unit (on DX systems only), and the wiring and cabling between the

wall-mounted iCOM display for all system types. Detailed connection information is included in the

submittal drawings listed in Table 5.1 on the previous page.

Connect field-supplied, shielded, Class 1 wiring from the condensing unit to the indicated terminal-strip

locations.

For the wall-mounted iCOM-controller display:

•

Connect a field-supplied, CAT5 Crossover Ethernet cable between P64 on the iCOM-control

board in the Mini-Mate module and ETH-1 on the wall-mount iCOM display.

•

Locate the wire harness inside the wall-mount display, and connect field-supplied, Class 1

wiring between the harness and landing on the terminal-strip 13, 14, and 15 in the Mini-Mate

module to provide power for the display.

For the wall-mounted temperature/humidity sensor:

•

Plug the factory-supplied, CANbus cable into P66 on the iCOM-control board in the Mini-Mate

module and into P66, Ethernet connection on the temperature/humidity sensor.

Vertiv | Liebert® Mini-Mate™ Installer/User Guide

Содержание Liebert Mini-Mate MT036

















































































Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды

Vertiv Liebert Mini-Mate MT036, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды