Vertiv Liebert Mini-Mate MT036 Скачать руководство пользователя

Страница: 5 / 80

1 IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions that should be followed during the installation and

maintenance of the Liebert® Mini-Mate. Read this manual thoroughly before attempting to install or

operate this unit.

Only qualified personnel should move, install or service this equipment.

Adhere to all warnings, cautions, notices and installation, operating and safety instructions on the unit

and in this manual. Follow all installation, operation and maintenance instructions and all applicable

national and local building, electrical and plumbing codes.

WARNING! Arc flash and electric shock hazard. Open all local and remote electric power-supply

disconnect switches, verify with a voltmeter that power is Off and wear appropriate,

OSHA-approved personal protective equipment (PPE) per NFPA 70E before working within the

electric control enclosure. Failure to comply can cause serious injury or death. Customer must

provide earth ground to unit, per NEC, CEC and local codes, as applicable. Before proceeding

with installation, read all instructions, verify that all the parts are included and check the

nameplate to be sure the voltage matches available utility power. The Liebert® controller does

not isolate power from the unit, even in the “Unit Off” mode. Some internal components require

and receive power even during the “Unit Off” mode of the controller. The only way to ensure

that there is NO voltage inside the unit is to install and open a remote disconnect switch. Refer

to unit electrical schematic. Follow all local codes.

WARNING! Risk of over-pressurization of the refrigeration system. Can cause explosive

discharge of high-pressure refrigerant, loss of refrigerant, environmental pollution, equipment

damage, injury, or death. This unit contains fluids and gases under high pressure. Use extreme

caution when charging the refrigerant system. Do not pressurize the system higher than the

design pressure marked on the unit's nameplate. Local building or plumbing codes may require

installing a pressure-relief device in the system.

Do not close off any field-installed, refrigerant-line isolation valves for repairs unless a

pressure-relief valve is field- installed in the line between the isolation valve and the check valve.

The pressure-relief valve must be rated 5% to 10% higher than the system-design pressure. An

increase in ambient temperature can cause the pressure of the isolated refrigerant to rise and

exceed the system-design pressure rating (marked on the unit nameplate).

WARNING! Risk of contact with high-speed, rotating fan impeller blades. Can cause injury or

death. Open all local and remote electric power-supply disconnect switches, verify with a

voltmeter that power is off, and verify that all fan impellers have stopped rotating before

working in the unit cabinet.

WARNING! Risk of electric shock. Can cause serious injury or death. The Liebert® iCOM

microprocessor does not isolate power from the unit, even in the "Unit Off" mode. Some internal

components require and receive power even during the "unit off" mode of the Liebert® iCOM

control. Open all local and remote electric power disconnect switches and verify with a

voltmeter that power is Off before working on any component of the system.

CAUTION: Risk of contact with sharp edges, splinters, and exposed fasteners. Can cause

injury. Only properly trained and qualified personnel wearing appropriate, OSHA-approved PPE

should attempt to move, lift, remove packaging from or prepare the unit for installation.

1 Important Safety Instructions

Содержание Liebert Mini-Mate MT036

















































































Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды

Vertiv Liebert Mini-Mate MT036, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды