Vertiv Liebert Mini-Mate MT036 Скачать руководство пользователя

Страница: 38 / 80

The motor also provides locked rotor protection, undervoltage/phase failure detection and motor current

limitation. These conditions will display an alarm through the Liebert® iCOM.

9.2.3 Fan Assembly Troubleshooting

Any safety hazards stemming from the device must be re-evaluated once it is installed in the end device.

Do not make any modifications, additions or conversions to the fan assembly without the approval of

Vertiv.

WARNING! Risk of electric shock. Can cause serious injury or death. Open all local and remote

electric power-supply disconnect switches and verify with a voltmeter that power is off before

opening the fan motor electric-connection enclosure. Use only fully-trained and qualified HVAC

technicians to replace or perform maintenance on the EC fans.

WARNING! Risk of contact with high-speed rotating fan blades. Can cause serious injury or

death. Open all local and remote electric power-supply disconnect switches, verify with a

voltmeter that power is off, and verify that all fan blades have stopped rotating before working

in the unit cabinet or on the fan assembly. If control voltage is applied, the fan motor can restart

without warning after a power failure.

CAUTION: Risk of exposure to harmful noise levels. Can cause hearing injury or loss.

Depending on the installation and operating conditions, a sound pressure level greater than

70 dB(A) may arise. Take appropriate technical safety measures. Operating personnel must

wear appropriate, OSHA-approved PPE and observe all appropriate hearing-protection safety

requirements.

CAUTION: Risk of contact with hot surfaces. Can cause injury. The compressor, refrigerant

discharge lines, fan motor, and some electrical components are extremely hot during unit

operation. Allow sufficient time for them to cool to a touch-safe temperature before working

within the unit cabinet. Use extreme caution and wear appropriate, OSHA-approved PPE when

working on or near hot components.

NOTICE

Risk of improper power-supply connection. Can cause equipment damage and loss of warranty

coverage.

Prior to connecting any equipment to a main or alternate power source (for example: back-up

generator systems) for start-up, commissioning, testing, or normal operation, ensure that these

sources are correctly adjusted to the nameplate voltage and frequency of all equipment to be

connected. In general, power-source voltages should be stabilized and regulated to within

±10% of the load nameplate nominal voltage. Also, ensure that no three-phase sources are

single-phased at any time.

NOTE: Do not assume that the fan blades will not start to spin. If the motor is in a fault condition, it will

safely shut down. Once the fault condition is cleared, there are certain conditions in which the motor

will automatically resume operation.

NOTE: Further troubleshooting procedures relating to fan connection/operation in the thermal

management unit are included in

Blower troubleshooting

Vertiv | Liebert® Mini-Mate™ Installer/User Guide

Содержание Liebert Mini-Mate MT036

















































































Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды

Vertiv Liebert Mini-Mate MT036, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Liebert Mini-Mate MT036

Отзывы:

Похожие инструкции для Liebert Mini-Mate MT036

Бренды по названию

Популярные бренды