Vertiv Liebert DSE Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 120

background image

Liebert DSE

™ Model DA250

SL-18945_REV2_9-18

12

Guide Specifications

3.21 DIGITAL SCROLL SENSOR FAILURE

The control shall monitor the status of the digital scroll sensor(s). If the control senses the
thermistor becomes disconnected, shorted or the reading goes out of range, the user will be notified
through an event on the local display and remote monitoring.

3.22 COMPRESSOR SEQUENCING

A user-selectable compressor sequencing parameter shall be provided and access through the local
control. This sequencing parameter presents the user with three choices:

•

Always use Compressor 1 as lead compressor.

•

Always use Compressor 2 as lead compressor.

•

Auto: The unit shall automatically stage compressors to keep each unit's run time within 8
hours of the other unit's run time. NOTE: The Auto setting attempts to maintain equal run
times between compressors. However, the control will not turn Off a compressor to equalize
run time when it is needed to control the space.

•

First priority

: If the safety timings are acceptable for only one compressor, that

compressor shall be the next to be started/stopped.

•

Second priority

: If both compressors are Off, the one with fewer working hours shall be

the next to start.

•

Third priority

: If both compressors are in operation, the one that has been operating

longer since the last start shall be the next to be stopped.

3.23 COMPRESSOR HIGH- AND LOW-TEMPERATURE LIMIT PROTECTION

The control shall monitor the return air to ensure that the compressor(s) are operated within the
manufacturer's defined window of operation. If the return air temperature deviates from the
manufacturer's window of operation, the Liebert iCOM shall automatically adjust to prevent
damage to the cooling unit or reduction in its reliability.

«
...
109
110
111
112
113
...
»

Содержание Liebert DSE

























































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert DSE

Бренд: Eaton Страницы: 50

Бренд: Eaton Страницы: 166

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: RAM Страницы: 32

Бренд: Rain Bird Страницы: 20

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

SaunaLogic SL2 Control

Бренд: Finnleo Страницы: 14

U-verse Advance Series A10

Бренд: AT&T Страницы: 2

Бренд: Goodson Страницы: 4

Бренд: Moeller Страницы: 2

ZoneSense Plus AS

Бренд: Halma Страницы: 58

PARTNER II Release 4.1

Бренд: Lucent Technologies Страницы: 363

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды