Vertiv Liebert DSE Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 120

background image

Liebert DSE

™ Model DA250

SL-18945_REV2_9-18

14

Guide Specifications

4.0 MISCELLANEOUS OPTIONS

4.1

HIGH-TEMPERATURE SENSOR—OPTIONAL

The high-temperature sensor shall be factory-installed in the unit and shall be factory-set to 125ºF
(52ºC). It shall immediately shut down the environmental control system when activated. The
sensor shall be mounted with the sensing element in the return air.

4.2

SMOKE SENSOR—OPTIONAL

The smoke sensor shall immediately shut down the Thermal Management system and activate the
alarm system when activated. The smoke sensor shall be mounted in the electrical panel with the
sensing element in the return air compartment. The smoke sensor is not intended to function as or
replace any room smoke detection system that may be required by local or national codes. The
smoke sensor shall include a supervision contact closure.

4.3

CONDENSATE PUMP, DUAL FLOAT—OPTIONAL

The condensate pump shall have a minimum capacity of 145 GPH (548 l/h) at 20 ft (58 kPa) head.
It shall be complete with integral dual-float switches, pump-and-motor assembly and reservoir. The
secondary float shall send a signal to the local alarm and shut down the unit upon high water
condition.

4.4

LOW VOLTAGE TERMINAL PACKAGE—OPTIONAL

Factory-installed and factory-wired terminals shall be provided.

•

Remote Shutdown Terminals

- 2 additional pairs of terminals provide the customer with

additional locations to remotely shut-down the unit by field-installed devices or controls.

•

Extra Common-Alarm Contacts

- 2 additional pairs of terminals provide the customer with

normally-open contacts for remote indication of unit alarms.

•

Main-Fan Auxiliary Switch

- 1 set of normally-open contacts wired to the EC-fan motor

contactor will close when EC-fan operation is required. This set of dry contacts could also be
used to initiate air economizer operation. Air economizer and associated devices by others.

•

Liqui-tect Shutdown

- 1 pair of dry contacts for the Liqui-tect sensor signal will provide unit

shut down. (Liqui-tect sensor is not included.)

4.5

REMOTE HUMIDIFIER CONTACT—OPTIONAL

A pair of N/O contacts provided for connection to a remote humidifier that allow the unit's
humidity controller to control a humidifier outside the unit. Power to operate the remote humidifier
does not come from the unit.

4.6

FAN OVERLOAD

The fan fault alarm is standard on all models.

4.7

COMPRESSOR OVERLOAD—STANDARD

A pair of N/O contacts shall be factory-installed and wired to each compressor to indicate
Compressor Overload.

«
...
111
112
113
114
115
...
»

Содержание Liebert DSE

























































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert DSE

Бренд: ABB Страницы: 2

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Wavelink Страницы: 69

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: IFM Страницы: 49

Бренд: IFM Страницы: 13

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Dantherm Страницы: 20

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды