Vertiv Liebert CRV CRD10 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 126

background image

Installation

Vertiv | Liebert CRD10 | User Manual

18

2.4

Transportation & Movement

WARNING! Risk of top-heavy unit falling over. Improper handling can cause equipment damage, injury
or death. Read all of the following instructions and verify that all lifting and moving equipment is
rated for the weight of the unit before attempting to move, lift, remove packaging from or prepare
the unit for installation.

WARNING! Risk of unsecured unit rolling off pallet. Can cause equipment damage, injury or death.
The unit is on casters. Ensure that the unit/pallet is located on a flat surface before loosening the
hardware securing the to its shipping pallet.

CAUTION: Risk of contact with sharp edges, splinters, and exposed fasteners. Can cause injury. Only
properly trained and qualified personnel wearing appropriate, OSHA-approved PPE should attempt to
move, lift, remove packaging from or prepare the unit for installation.

NOTICE!

Risk of doorway/hallway interference. Can cause unit and/or structure damage. The unit may be too
large to fit through a doorway or hallway while on the skid. Measure the unit and passageway
dimensions, and refer to the installation plans prior to moving the unit to verify clearances.

NOTICE!

Risk of damage from forklift. Can cause unit damage. Keep tines of the forklift level and at a height
suitable to fit below the skid and/or unit to prevent exterior and/or underside damage.

NOTICE!

Risk of improper storage. Can cause unit damage.

Keep the unit upright, indoors and protected from dampness, freezing temperatures and contact
damage.

Transportation by rail or by ship are the preferred options for the units. If transport by rail or by ship is
unavailable, transport by road is recommended. When selecting road transport, roads without too many
bumps are highly recommended.

•

Liebert CRD10 unit is heavy, it is recommended to use the mechanical equipment like electrical forklift to
move the unit.

•

Move the equipment to the location near the installation site.

•

If an electric forklift is used, insert the tines of the forklift below the pallet as displayed in Figure 2-2.

•

Figure 2-2 shows how the forklift tines are inserted underneath the pallet and shows in the same picture
below the illustration to the right that the lines should be aligned with the center of gravity to prevent the

«
...
28
29
30
31
32
...
»

Содержание Liebert CRV CRD10 Series































































































































Отзывы:

Нет отзывов

Похожие инструкции для Liebert CRV CRD10 Series

PREFERRED 124ANS

Бренд: Bryant Страницы: 6

Бренд: GE Страницы: 36

Бренд: American Comfort Страницы: 15

Бренд: iGenix Страницы: 24

Classic 20 CS020020A

Бренд: Dantherm Страницы: 16

40MKCB**F/24AHA4

Бренд: CAC / BDP Страницы: 24

Бренд: emmeti Страницы: 112

BAYECON353 Series

Бренд: Trane Страницы: 24

OTEC ICHD009J0A-DMG026

Бренд: Omega Страницы: 67

DIFFUSIONE 10.5 HP HE

Бренд: Olimpia splendid Страницы: 108

Бренд: Daikin Страницы: 355

Бренд: Daikin Страницы: 22

Mini-Floor Console A Series

Бренд: Gree Страницы: 18

Бренд: Envicool Страницы: 31

Бренд: Daikin Страницы: 13

Бренд: Jata Страницы: 16

Бренд: Jata Страницы: 16

Бренд: Panasonic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды