Vertex 10G107 Скачать руководство пользователя страница 5

Страница: 5 / 16

Form: Man10G107 Rev. –C-

02-06-2012

III. What’s in the Box & What You Will Need

After you unpack your machine and see the quality construction we know that it will be tempting

to jump right in and get things going. Please take a few minutes to ensure that everything listed

below has been removed from the packaging and take note of what else you will need to begin

annealing.

Contents:

Inside the box is a poly bag containing (4) Leveling Feet, (2) Nylon Washers, (2) Clamp Knobs,

(2) Clamp Sets for securing your torch nozzles and (1) Clamp Plate. Also included is your AC

Adaptor to power the electronics & drive motors. You should find separately packaged, a

Carrier Plate for indexing your cartridge cases. Please see below….

Assembly:

1. After removing the contents from the package, please turn your annealing machine up side

down and screw the (4) adjusting feet into the bottom of the tapped holes in the legs.

2. Right the machine with the index sprocket and clamp posts up as shown on the cover of this

manual.

3. Place the Carrier Plate over the 5/8 diameter pin in the Sprocket with the two ¼ studs

passing thru the kidney shaped slots in the plate. Make sure that the Carrier Plate rotates freely

around the 5/8” pin.

4. Next place the Clamp Plate over the studs (with the bevel side up) and the 5/8” center pin.

Top these off with (1) Nylon Washer and (1) Clamp Knob on each stud. It is not necessary to

tighten the knobs more than finger tight. Carrier Plate orientation is not important at this point.

Содержание 10G107
















