20304166
VC31LDVI/VC31CDVI Gas Fireplace Insert
33
setting privacy Code on transmitter:
Figure 36
The remote transmitter privacy code
is preset in factory. In the event of
activation or interference from other
nearby transmissions, change the
code using the following procedures
(learn function must be performed
after changing the code):
1. Press the ON/arrow button and
the TIMER button at the same
time to enter privacy code setup
mode.
2. The setup display is shown in the
figure. The four digits on the top
stand for the privacy code (as the actual DIP switches
on Ambient’s previous remotes). The default values of
the four digits will be all “1” (ON).
3. The first digit will be flashing upon entering the setup
mode. Push the ON button to toggle its value between
“0” (OFF) and “1”(ON), and push the “OFF” button
to jump to the next digit. The next digit will then start
flashing and the first one stops flashing. Set up the
four digits to your choice.
4. After setting up all the four digits, push “OFF” to finish
the process and return to the previous mode.
5. The Signature Command control board then needs to
re-learn the new setting.
performing learn Function
1. The RF receiver button on the control board in the fire-
place must be in the on position before the learn func-
tion can begin.
Figure 37.
With the Command Center
master switch in the ON position, use paper clip to de-
press the recessed button on Control Board, one beep
for RF receiver ON or two beeps for RF receiver OFF
2. Holding the OFF
button on the Com-
mand Center while
turning on the
master switch will
activate the learn
function for the
transmitter.
3. After the above op-
eration, two beeps
will be given and
the green LED on
the Command Cen-
ter will flash for 10
seconds.
4. During the 10 sec-
onds, press the OFF button on the transmitter to learn.
Another two beeps will be given to confirm a success-
ful learning.
Figure 38
tOuCh sCReeN RemOte CONtROl OpeRAtION
FP2649
set privace code
FP2650
command ctr ctrl brd
RF Receiver
ON/OFF
Control Board
FP2650
command ctr ctrl brd
Battery Door
Master Switch
ON
LED
OFF
FP2650
Command Center
Figure 31
Figure 37
Figure 38
W
ARNING
Do not use two (2) or more remote control sys-
tems in the same area with the same privacy
code setting, as they will communicate with
each other. this may cause the appliances to
malfunction.
Resetting the transmitter:
If the transmitter is not working properly, reinstall the bat-
teries to reset the transmitter.
1. Pull out at least one of the batteries.
2. Press any key on the screen to discharge.
3. Wait for 10 seconds and reinstall the batteries.
Pushing and holding any key for more than 10 seconds
until the display refreshes will also reset the transmitter.
n
Functions and Operations
General:
The TSFRSC Remote Control has four (4) operating
modes: Manual, Timer, Thermostatic and Smart Mode
®
Thermostat. The control system can be set to tempera-
ture range between 45° F and 90° F. The blower speed
and flame height can be adjusted in the manual, timer
and thermostatic mode. The Smart Mode
®
thermostat
will automatically adjust flame height and blower speed
according to the difference between Set and Room tem-
peratures.
The transmitter will operate the remote receiver from 1
foot to a maximum of 30 feet. The distance is reduced
when batteries are low.
manual mode
Figure 39
In this mode, the TIMER button and the THERMO but-
ton will only display “TIMER” and “THERMO”, respec-
tively without showing the time and the SET temperature.
Pressing the ON/up and OFF/down buttons will change
the flame height if none of the menu buttons (TIMER,
Figure 36