Vermont Castings VC31CDVINTSC Скачать руководство пользователя страница 16

Страница: 16 / 48

20304166

VC31LDVI/VC31CDVI Gas Fireplace Insert

INstAllAtION

INtAKe/exhAust mANIFOlD RemOVAl

AND VeNt INstAllAtION

The intake/exhaust manifold is shipped attached to insert.

It may be removed to allow tight installation.
1. Unfasten the two (2) machine screws on the face of the

unit and release the plate assembly by sliding the plate

back.

2. Attach the exhaust and the intake flex pipes to the collar

on the plates with a hose clamp (not provided) or other

approved methods (check local codes).

The unit is shipped from the factory without a baffle

installed. On the natural gas units, the baffle should be

sufficient for venting up to 20 feet (6 m) off the top of the

unit. An extra baffle plate is shipped with the unit for instal-

lations of 20 feet and above.
Remove four (4) screws holding baffle plate. Add extra

baffle pate and reinstall screws. Align slots in baffle plates

so the slots are closed. Retighten screws.

NOte:

For propane (LP) units the baffle assembly is com-

pletely removed for venting under 20 ft. (6 m). For venting

20 ft. and above, the baffle assembly is to be used with

only one (1) baffle plate installed.

Figure 17

FP1961
baffle adjustment
9/08

Loosen Four (4) Screws to Adjust

Bottom View

Closed position

Bottom View

Open position

FP1961

Figure 17 -

Baffle Assembly and Adjustment

3. Slide plate assembly back in place under locating

tabs.

4. While sliding unit in place, if necessary the glass latch/

shutoff tool can be used to help place the plate assem-

bly. Using the small end of the tool, insert it in the square

notch in top front of firebox. Hook the plate assembly

with tool and pull forward into place while sliding firebox

to the rear.

Figure 16

5. Reinstall and tighten machine screws.

FP2977
latch tool plate assy

Plate

Assembly

Latch Tool

FP2977

Figure 16

FP2979
intake exhaust

Figure 15

Machine

Screws

Intake Collar

Exhaust/Intake

Slide Plate

Assembly

FP2979

Exhaust Collar

Failure to install the baffle assembly on

natural gas units may result in smaller than

normal flame appearance.

Содержание VC31CDVINTSC

















































Результаты поиска

Содержание VC31CDVINTSC

Отзывы:

Похожие инструкции для VC31CDVINTSC

Бренды по названию

Популярные бренды

Vermont Castings VC31CDVINTSC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VC31CDVINTSC

Отзывы:

Похожие инструкции для VC31CDVINTSC

Бренды по названию

Популярные бренды